Forum Replies Created
-
Posts
-
Re: Fitting a drive Belt to Hotpoint washing machine
HI
Whats the Model number of machine And the part number of the belt you have So that we can check
Mike
Re: Proline DW6006 Heater
Hi all
Hope its the right one I have ordered it from Masterpart
Comet do not hold it as a stock item and have no idea if they could even get one .Mike
Re: oven door seal
Hi
Tecnogas is part of Antonio Merloni ie Servis
This model comes up as Proline GF601W and Part number 420064800 for door seal on Servis/Tecnogas diskIf this is any help
MikeRe: diplomat outer tub
Hi All
Original tub part no 726004400
modified tub part no 726015000
modified tub needs new soap hose as tub soap hole in different position
modified tub with hose part no 750187100
£83.00 plus vat on Servis price listMike
Re: samsung washer
Hi Graham
TEST MODE
Hold down Rinse and spin buttons and press power sw
Then press start button
Test sequence will begin 3 times
Pre Wash valve on 1 sec off 1 sec
Cold valve on 1 sec off 1 sec
Shower valve on 1 sec off 1 sec
Hot valve on 1 sec off 1 sec
Drain pump on 1 sec off 1 sec
DDD pump on 1 sec off 1 sec
Motor left on 1 sec off 1 sec
Motor right on 1 sec off 1 sec
Heater relay on 1 sec off 1 secThermister test
Hold down Rinse and spin buttons and press power sw
All lamps light display shows T1 after 30 sec
Press rinse and display shows t2 after 30 sec
Press start button and display shows temp of wash tub .Mike
Re: samsung washer
Hi Graham
OVER CURRENT ERROR – Display shows 8E .
– IPM fault signal (that is caused by the overload of MICOM INT0 during motor action) is sensed.
IPM : Integrated power module. , IPM controls motor.
– If the fault signal (low signal) happens to be sensed even one time during cleansing/rinsing stage,
the motor stops immediately.- During Cleansing or Rinsing
When the overload is sensed, the motor stops immediately and then proceeds to the next water-flow action.
If the stopping of the motor working is happens in one direction ten times,
“8E” Error is displayed.
When the overload is sensed, the motor stops to work at once and then feeds back to the initial stage unbalance sensing.
When it happens at more than 800rpm, the process is stopped -Power S/W Off can clear the overload error.Is this any help
MikeRe: Can I vent a cooker hood up a chimney?
Hi
Do’nt forget that you can get down drafts from chimneys as well . which means things will get blown back into cooker hood from above .
Washman
Re: Hotpoint 9326 Tumble Dryer
Hi
It’s suffering from old age , and is time it retired .
The bearings and everything else is worn out .Washman
Re: Servis washer dryer pump M9634
HI
9634 is old type servis made washer dryer not showing up on Servis disk
most likely Connections PMP921Mike
Re: The connections game! (Which tier are you on?)
Hi All
My prices from connections are
PLM4702 — £0.43
HPT1702251 — £9.94
WPL481225928675– £13.72
DST50239964005 — £14.70
HVR04350196 — £9.33
MER074213 — £30.34
BSH096825 — £54.95Mike
Re: Asko dishwasher spares
HI all
Lower plate rack for 1402 is part no 8052162 in ASKO parts manual .
this is a seperate part from the main lower basket
Electrue shows this as a special order with SSP of £23.92Mike
Re: Asko Asea table top model 750
Hi Bill
The 750 is the original machine that was also sold as an Ariston for a while can’t remember mod no . This one DW 750 has the door that pops open at the end of the cycle so is getting on abit . the manual is dated 1986-08
I have manuls for lots of older Asko /Asea machines.Mike
Re: Ariston fan element
Hi All
My price from Connect is £4-10 for gen and £3-60 for pattern If you ask nicely they will give you a better discount rate
Mike
Re: Asko Asea table top model 750
HI ALL
Bill are you sure this is correct spring part number as I have just looked in my ASKO service manual for 750 dw and it shows door spring as p no 7840019 and calls it lid brake spring this also comes up on Connect under this part number .
Washman (mike)
