Washman

Forum Replies Created

Viewing 15 posts - 691 through 705 (of 894 total)
  • Author
    Posts
  • in reply to: Samsung q1235v/xeu #192072
    Washman
    Participant

    Re: Samsung q1235v/xeu

    Hi

    8E is over current error.
    If motor just judders its probably the module at fault. But check motor out as well.

    Mike

    in reply to: Hoover D6008 #192012
    Washman
    Participant

    Re: Hoover D6008

    Hi

    Try Electrue part no BLT901 shows in stock.

    Mike

    in reply to: beko 2 same fault #191765
    Washman
    Participant

    Re: beko 2 same fault

    Hi

    Try this reset
    the fix for flashing pre wash led, or flashing start/cancelbutton is

    Turn power button off (not at wall)
    Select 90 degree wash
    Press Start and Cancel button down at same time for 3 seconds and turn power button on whilst still holding buttons down – Start light will flash.
    Leave power on.
    Select any Spin position.
    Press Start and Cancel button at same time again for 3 seconds – other buttons may start to flash – if they do, press Start and Cancel button together again for 3 seconds.
    Machine should be re-set ready for use.


    Mike

    in reply to: Servis dispenser part no’s? #191196
    Washman
    Participant

    Re: Servis dispenser part no’s?

    Hi

    Bottom 348004900
    Top 330109600

    Mike

    in reply to: Bosch or Stoves ? #188140
    Washman
    Participant

    Re: Bosch or Stoves ?

    Hi

    A fan oven cooks at a lower temperature and in less time so saves you money. If you cook at conventional oven temp and times in a fan oven you will end up burning everything. You need to get a good new cookery book,which should have a conversion table in it for fan and conventional ovens. A fan oven temp should be the same on top and bottom shelves.

    Mike

    in reply to: samsung washer #189926
    Washman
    Participant

    Re: samsung washer

    Hi

    Its the PCB needs changing.Its a common fault.

    SAMSUNG Part no MSF-Q1435-01

    Mike

    in reply to: Yellow sludge on Siemens filters. #189659
    Washman
    Participant

    Re: Yellow sludge on Siemens filters.

    Hi

    I had this once, and found that the water was not reaching high enough temperature to disolve fats and grease of dishes. Changed stats and all was OK . I allways check water temperature now on any dishwasher job.

    Mike

    in reply to: Hoover w/m, I have spent £80 on a timer to no avail, help! #189564
    Washman
    Participant

    Re: Hoover w/m, I have spent £80 on a timer to no avail, hel

    Hi

    Have you checked motor brushes by removing them.

    Mike

    in reply to: Hotpoint Aquarius WMA31 noisy spin followed by shut down! #189438
    Washman
    Participant

    Re: Hotpoint Aquarius WMA31 noisy spin followed by shut down

    Hi

    It could be motor Brushes also if motor spins and stops

    Mike

    in reply to: servis module #189423
    Washman
    Participant

    Re: servis module

    Hi

    Part numbers are on all servis modules and usually start with 546

    Part number for module fitted to M0330S is 546017100
    SER546017100 IN STOCK ELECTRUE/CONNECT £45.90
    ARD546017100 IN STOCK MASTERPART £29.99

    Mike

    in reply to: Servis M9505 WD won’t start #188894
    Washman
    Participant

    Re: Servis M9505 WD won’t start

    Hi

    Set program knob to “OFF” position and switch machine on and wait a few seconds this should reset module.If not what ever caused power cut may have damaged module.

    Mike

    in reply to: creda tcr2 condenser dryer thermostat #188846
    Washman
    Participant

    Re: creda tcr2 condenser dryer thermostat

    Hi

    Do not stop the dryer mid cycle to check on how dry the load is, always let it continue to the end and complete the cool down phase.

    Mike

    in reply to: SCHREIBER LARDER FRIDGE APP6032 #188831
    Washman
    Participant

    Re: SCHREIBER LARDER FRIDGE APP6032

    Hi

    Its made by Servis for MFI Stat part number on Connect SER526012100 in stock srp £27.00 or Masterpart ARD526012101 buy for £14.99

    Mike

    in reply to: servis easiwah washing machine #188688
    Washman
    Participant

    Re: servis easiwah washing machine

    Hi

    You have to seperate the two halves of the door and swing the outer part of frame around to gain access to the screws, make a note of the springs. when refitting push the handle on after door is back together

    Mike

    in reply to: servis easiwah washing machine #188686
    Washman
    Participant

    Re: servis easiwah washing machine

    Hi

    Model no and serial no please as there are many variations

    Mike

Viewing 15 posts - 691 through 705 (of 894 total)