Forum Replies Created
-
Posts
-
Re: Haier faier….
0020400542X Part number for the Selenium Rectifier on Haier washing machines. Don’t forget, they are made in China and they still use a lot of stuff that the West stopped using long ago. One of the sales guys from China that was over last year was trying to plug brand new chest freezers with R12 😉
Re: Haier HW-C1470TVE Parts diagram / pictures of parts
The Selenium rectifier on the Haier is positioned on the rear right corner near to where the mains lead comes in, the wires from this to the front main pcb is protected by an inline fuse. I have never seen any problems with either the boards or the selenium rectifier (part number 0020400542X) but the motors have given problems, especially the brushes which are a common problem
Re: rosieres 2040 range cooker
Sorry, just noticed that you said Range, could do with the product number to help as when you type 2040 in Giastech there are loads. Do have a pdf file that I could send if you have an email but it’s in Italian
The model is a 2040cDB-dDB Range cooker made between 1/6/88 to 22/3/93.
I go to one in North Wales in Bala which is LPG and you can still get most partsRe: rosieres 2040 range cooker
Made by Candy, could do with product numbers to confirm parts but if it’s the single built in oven (FR2040) with a product number 36279016 then the part number for the door hinge from GIAS is 91750365.
Part is still available, cooker started production circa 2000Ignore me, see below
Re: Hotpoint WMF740 Door Interlock
Motor or Wiring to motor causes this fault, very very common fault
Re: lec f/freezer tf6086
The small pcb in the fridge roof is just a small variable rheostat, The pcb is on the back of the appliance and it is made by beko in Turkey. Parts are available from Glen Dimplex ( stoves,newworld ) in Prescot. Check your email for the bulletin when they changed from manual stats to display
Re: Hotpoint uy46xmk2 clock wireing diagram
Need the commercial code/ industrial code as 3 versions of the mk2 and each one is wired differently, depends also if its Italian or Polish
Re: Zanussi washing m/c FL1082 914789533/02
Martins correct, pnc number is 914789553.
We had a similar problem, no info on the 02 production code. however the prev product codes of 01 where produced in both the ITZ and Porcia factories with the more up to date Sole motor which was 1242778007.
This one worked when we fitted itRe: indesit IS70C tumble dryer
Been in production over 6 months now, more money making from merloni, you have to change the whole drum unless your good with an angle grinder :rolls:
Re: Integrated Dishwashers !!!!
Went to an LPG Delonghi range cooker last year and the kitchen fitters had poured concrete level mix across the floor and the 4 legs were buried into 1″ deep cement, then I noticed the Dishwasher, Dryer & Washing Machine were the same. Actually felt sorry for her and told her to get back in touch with B&Q who had used contracters.
Re: Fisher & Paykel
Loads of varients of that model, you could try 0845 062 2300 which is F&P technical line for there own Service agents, see if they can help
Re: Hotpoint TVF770P
Just to add a bit more to Martins reply
C00112196 was from serial 40501
C00262243 was from serial 70802
The heater assy is C00277074From Serial Number 70802, Two different Heater manufacturers were used in production. These DBK and Blaissi Heaters are totally interchangeable if replaced as an assembly.
But the thermostat kits for these Heaters are not interchangeable.
From Serial number 70802, before a Stat. Kit is replaced the heater fitted to the machine must be identified first.
The cover of the Blaissi heater has 2 raised dome shaped pips, there is also a Blaissi Label inside the heater attached to the inside of the heater cover
The Cover of the DBK Heater has 4 raised dome shaped pips.DBK heaters and covers are used as service spares, therefore if a heater or cover have previously been replaced further identification is required.
The DBK heater element wire is in a strip.
The Blasi heater element wire is circular.For the Dryer to work correctly the correct Heater and Stat. Kit must always be fitted.
😉
Re: drcs68 dryer
Beko carried out a mod in November and the front assy has changed so I am assuming yours is the original. The part number for the front felt is 2961080100 and should have adhesive on the back. This sticks to the duct and the adhesive faces away from the drum. The lip of the drum pushes into the felt which is the opposite face to the adhesive
