Forum Replies Created
-
Posts
-
Re: indesit wdg1295w
2 types on this model depending on serial. after 80118 it’s C00032850, if it’s before date code 80118 it’s C00045394 😉
Re: need a wiring diagram for hotpoint ew74g
sent you the full service manual and tech bulletin K. 8)
Re: Electrolux cooling fan EOB5100X
JUST CHECKED ON OUR UP TO DATE PROCORNER SITE. PART YOU ORDERED IS CORRECT ( 3570594063 )
Re: ADP8332 F9
ADP8332 is a Whirlpool product so I think the following may be applicable
8)Whirlpool Dishwasher Error codes.
F0. 10 flashes. Sensor Break (Only shown in test programme. Not visible to customer).
F1. Single flash. NTC Break. NTC open circuit/short circuit or ambient temperature less than 3
Celsius
F2. 2 Flashes. Water leakage. Floater switch LS6 in drip tray has switched.
F3. 3 Flashes. Heating system defect. Heater or relay on control board defect. Check also cabling.
F4. 4 Flashes. Draining failure. Drain pump, control board OWI or water indicator defect.
F5. 5 Flashes. Spray arm Blocked (not present on VBL version. On 1 digit display will show as F
and flashing start led).
F6. 6 Flashes. Water valve (WV1) is switched on but flow meter (FM) senses no impulses (less
than 10 impulses in 10 secs.) and the water indicator (WI) is at a low level
Water Valve Closed. Water inlet hose blocked.
Water inlet valve (WV1) defective. Flow meter (FM) defective (leads to FM failure)
F7. 7 Flashes. Flow meter failure. Flow meter defect. Water inlet valve defect or water inlet hose
blocked.
F8. 8 Flashes. Water level failure. Sieve strongly dirty or big amount of foam inside to less water.
F9. 9 Flashes. Continuously Water Inlet. Water inlet valve mechanically not closed or control board
defect.
FA. 11 Flashes. OWI failure. Dirty OWI lens. OWI defect or control board defect. Check cabling.
FB. 12 Flashes. Motorised Diverter Valve
FC. 13 Flashes. Water Hardness Sensor Failure
A fault with no fault code indication = faulty module
These codes should cover the entire range of Whirlpool dishwashers.
Test Mode
Make sure the appliance is empty of water before running Diagnostics as it does not
pump out before starting to fill and therefore you could overfill the appliance.
Open the door and set the program to the first program. (Normally rinse).
Turn the power off.
Press and hold the start button and while holding turn the power on.
After a little while the start button will flash, release the button.
Press the start button once and close the dishwasher door.
The machine will now run through a diagnostic routine.
If memory serves me right it takes about 20 mins.
The machine will stop during diagnostics if an error is found and will display the error code. If no
error is found it will complete the diagnostics and end the programme.
To exit diagnostics at any time just press and hold the start button till the programme is cancelledRe: Proline CHIM60A cooker hood switch
Appliance is made by ELICA in Italy. Dont know how you get spares, the assembly is not available as a spare but all the bits are
lower part of housing – 30851FHE
upper part of housing – 3007FJ
plastic light slide – 3034AHA
plastic motor slide – 3035ACX
electric light switch – 2011G
electric motor switch – 2011HRe: whirlpool 3RLEC8600SL-1
3387749 heating element. not sure who supplies but loads listed on google
Re: whirlpool 3RLEC8600SL-1
model not recognised on WEDOC. Have you the 12 digit product code beginning with 8
Re: Stinky Pete
hahaha, familier story, even worse when you drive 120 miles to your first job and can’t nip back to change. Introduce the dog to your megga attched to a long shafted screwdriver and touch his NADS, he will stay clear, I promise you 😯
Re: felt bearing beko drcs 68w dryer
BACK OFF, DRUM OUT AND DEAD EASY TO GET TO, JUST DOUBLE SIDED ON ( HOWEVER ). Beko have now changed the design due to this fault, when you change the felt, it will last a week or so then come off again, jams the drum and snaps the belt. This is the major cause of snapped belts and we are doing about 10 full rebuilds under 1st year a week for Beko and they are a ball ache. The design change entails fitting a whole redesigned front duct and bearing assembly and redesigned drum, they are not interchangable. :rolls:
If you just want the part number for the stick on cloth bearing its 2961080100Re: HOOVER HCA383 INTER@ct F/F
Known fault on this appliance. I have the GIAS tech bulletin but need an email to send it too you as cannot publish here
