Forum Replies Created
-
Posts
-
Re: Zanussi Washer Dryer Timer advancing
A coin in the return pipe to the pump (the 1 by the stats)
Hope this helps
Wvm
Re: What an idiot.
iadom wrote:Just seen this on another forum, sounds like one or two of our punters. 😀
What a numpty. 😆Jim.
News just in !
His wife has now filled for divorce he tried to do the same to her.
Re: Fairy Liquid Disaster – Whirlpool DWF416 (IKEA built in)
BillyWiz wrote:You’re not alone! Ours wasn’t cleaning too well, it often left a gungy residue in the bottom of cups. But we’re dafter than you, because rather than introduce Fairy liquid accidentally, we deliberately squirted some in without dishes, and set it off on a cycle. Same result as yours; a foamy kitchen and constant bleeping.
Did the fix work?
A very old tip, a handlful of table salt thrown in will help reduce foaming at time of accident.
Hope this helps
WVM
Re: Servis Washer/Dryer trips electrics if i try to use drye
:zap: Power off first :zap:
Remove lid, visualy check that no wires have broken of , failing that would suggest you contact a local repair man.
Try repairs@ highly recommended by other visitors to the board.
Hope this helps
WVM
Re: Zannussi Door Handle
EFS wrote:Looking for part No for FC 1200W (914010022) door handle
Any help appreciated
Steve
150 85 09-00/5
£3.28
Wvm
Re: bsh ff not cold enough
streetlighter wrote:Thanks for the replies
All I can get from bsh spares is frz sensor repair kit bsh 491415
connect show a pic of it and lord knows where you stick it 😯
is this the timer end or do I have to fit it sensor end where ever that is ❓
Ta for any helpPaul
you will get instructions how to if purchased from bosch
Re: AEG 72620 Drum support
iadom wrote:
Has anyone seen a drum support fracture on one of these German made tanks. ❓Jim.
Interesing liquids destroying supports, to be honest I’m not that convinced that it is down totally to the detergents, the reason I say that is some time I left a New tub (Hotpoint ) support outside in the elements by mistake, some months later the tub support had started to corrode, so is it part water/detergent either or both ????
Re: AEG 72620 bits
iadom wrote:Trying to find a price for parts for this AEG http://tinyurl.com/y6t5wn
8996451425707 gasket & 8996454250904 drum support. Both out of stock/POA at Masterpart. 😥
Jim.
8996451425707
Description: GASKET
£13.44 retail price
8996454250904
Description BEARING SPIDER,COMPLETE
superseded to 407 13 53-24/9
£34.94 retail priceDirect from electolux both items are in stock
Hope this helps
WVMRe: Candy Aquaviva
DentedPorsche wrote: Shame that you need the plug in unit to do anything.
Brian
and attached to a pc to look at motherboard error logs – see email
Re: Zanussi Duo bottom oven problem
cheeky wrote:i cant find the model no on the front/doors – the instruction book cover the “ZHF865 W/B/X”
WRT the top element – it looks like the wrong one was fitted. The clips dont fit in the holes in the side (2″ out) and there is no screw in the top. Too right its a safety issue – the missus has burnt her hand a couple of time. And its my safety if it doesnt get fixed asap!!! 😉
Read P30 of Instruction book, Heading – Problem – 3rd one down also
Screw required 311 36 09-00/6 mailto:spares@ukwhitegoods.co.uk
Re: A Warning
Gazman1000 wrote:I was in a house where two teenage kids were watching me work on a leaking Hotpoint top loader, I went out to the van for a pump, while I was away the little s*its pluged it back in for a laugh, I changed the pump and then went to the plug to do an earth test and saw it pluged back in, the two teenagers were laughing, the kids mother thought it was funny too!
I went ape, and had a slanging match with the stupid woman and her kids, I always double check if I turn my back on a machine now.Could have gone back to van, charged three capacitors and handed it terminals first, now that would have been funny 😆
