wizard

Forum Replies Created

Viewing 15 posts - 1 through 15 (of 167 total)
1 2 3 … 10 11 12
  • Author
    Posts
  • September 17, 2016 at 11:36 am in reply to: Bosch dishwasher – model SM150C12GB #441037
    wizard
    Participant

    Re: Bosch dishwasher – model SM150C12GB

    Yes, they turn themselves off now.

    September 10, 2016 at 4:59 pm in reply to: Bosch WAS32466 w/m No Spin #440633
    wizard
    Participant

    Re: Bosch WAS32466 w/m No Spin

    You’re welcome. Wiz

    September 4, 2016 at 7:37 am in reply to: Bosch WAS32466 w/m No Spin #440631
    wizard
    Participant

    Re: Bosch WAS32466 w/m No Spin

    Probably the 3D sensor , sits behind a big magnet on the rear of the drum. Part no615666. Wiz.

    August 23, 2016 at 12:10 pm in reply to: Hotpoint Tool Case 19 #440374
    wizard
    Participant

    Re: Hotpoint Tool Case 19

    Hi Keith, I spent a lot on a gt line case a couple of years back and always hated it. Partitions in lower section don’t stay where they’re put and unless you’ve got absolutely everything in a perfect position the lid won’t shut! Now there’s wearing in the hinges and stuff falls out. Won’t be having another, will probably go parat next time. Wiz

    August 19, 2016 at 6:07 pm in reply to: aeg f88060vi0p dishwasher #440286
    wizard
    Participant

    Re: aeg f88060vi0p dishwasher

    Sorry forgot pnc 911437004/06

    May 10, 2016 at 7:07 am in reply to: Bosch D/W ‘check water’ #437537
    wizard
    Participant

    Re: Bosch D/W ‘check water’

    Check water can also be an emptying fault.

    April 10, 2016 at 12:17 pm in reply to: beko dw686 pcb/module #436927
    wizard
    Participant

    Re: beko dw686 pcb/module

    Thanks, that’s what I thought – wanted to be sure. Wiz

    March 2, 2016 at 11:07 am in reply to: Bosch WKD28350GB/03 #433239
    wizard
    Participant

    Re: Bosch WKD28350GB/03

    Check the duct from the heater box to the door gasket, fluff builds up on the ntc and on the duct strengthening bars.

    November 27, 2015 at 6:01 pm in reply to: siemens sn66t091gb/28 #432994
    wizard
    Participant

    Re: siemens sn66t091gb/28

    Blown ‘low power on line switcher’ ic on main pcb. Hoping it was caused by a power surge, new pcb ordered.

    September 13, 2015 at 4:09 pm in reply to: Need advice on buying a vent hose #430243
    wizard
    Participant

    Re: Need advice on buying a vent hose

    Have it your own way Martin, but do give it a try when you’ve next got a vent hose in your hand.

    September 13, 2015 at 10:59 am in reply to: Need advice on buying a vent hose #430241
    wizard
    Participant

    Re: Need advice on buying a vent hose

    Go try it then Mr clever clogs !

    September 13, 2015 at 6:45 am in reply to: Need advice on buying a vent hose #430239
    wizard
    Participant

    Re: Need advice on buying a vent hose

    Not true Martin ! Do the threads go the opposite way on each end of a lenghth of metal studding ?

    August 21, 2015 at 6:59 am in reply to: Bosch SMS40C12GB/03…Door not locking #429754
    wizard
    Participant

    Re: Bosch SMS40C12GB/03…Door not locking

    Try it with baskets out, could be something fouling the door. Also check the white trim that meets the top edge of the door when closed, could also be fouling it. Wiz

    August 19, 2015 at 7:48 pm in reply to: bosch was32461 clothes still wet #429569
    wizard
    Participant

    Re: bosch was32461 clothes still wet

    Had one doing this a couple of months back – was the 3d sensor(lines up with big magnet on top rear of drum) . Wiz

    July 8, 2015 at 3:14 pm in reply to: Neff V6540X0GB/01 E13 Error #428682
    wizard
    Participant

    Re: Neff V6540X0GB/01 E13 Error

    Iirc e13 is a door lock fault, but normally caused by poor insulation resistance on the dry heater (they get damp cos people don’t use them). Try meggering it or disconnect if it’s never used. Wiz

  • Author
    Posts
Viewing 15 posts - 1 through 15 (of 167 total)
1 2 3 … 10 11 12