Forum Replies Created
-
Posts
-
Re: Samsung rls36sbms
Hi
Nope the heater can be ordered seperatly,in fact if i remember correctly a rl33 heater fits.
bryan
Re: Compressor size
Hi
the 1/4 compressor will work without a problem if its a r600a but if your fitting a r134a then you will need a 1/3
bryan
Re: gorenje washer dryer
would not the fagor parts be cheaper?
Gorenje parts are normally 50{e5d1b7155a01ef1f3b9c9968eaba33524ee81600d00d4be2b4d93ac2e58cec2d} cheaper than the companies that use their products..
smeg for example charge approx £60 for the fab freezer flap..gorenje £12.
bosch tumble drier heater £80 gorenje £15.
and as connect have the fagor supply contract and they increased the parts by £60{e5d1b7155a01ef1f3b9c9968eaba33524ee81600d00d4be2b4d93ac2e58cec2d} as soon as they got it..nope i dont think fagor would be cheaper.
bryan
Re: gorenje washer dryer
Hi brian
the following :
water heater part number 162504
drier heater part number 162511Bryan
Re: SMEG DI612 PUMP FAULT
Penguin45 wrote:Float switch is a diect mains feed, the pump is otherwise switched by the pcb, so it’s probably not OK.
Chris.
i fitted a new pcb as that is what i thought it was but it still done it. so im comfused
Re: Samsung RS21
Hi subs
try removing the PCB connectors and refit,other than that change the light switches.there isnt anything else it could be.
bryan
Re: Is This The New Craze?
I blame the credit crunch!……..re useing to save money….?
BUT ……..also environmentally friendly..!
CANUFIXITRe: NEFF B1641 oven dead
valentino246 wrote:Thanks very much for that, I will double check the connectors at the rear of the oven.
I did notice some dark burn marks on the main control unit nearest the point where the selector comes out. This is what made me think that that might have blown.
All help appreciated.
Thanks
So you have to replace that main unit ..Do you have warranty ???
Re: Dydon DC08 pre filter cleaning
Under close inspection, I’ve found that the trap door, on the collection housing, is cracked in a number of places.
I guess this isn’t helping any ??
Secondly, the rubber seal that fits on the lower part of the cyclone, and seals the cyclone to the trapdoor, is intact, and looks OK.
But when I conect the cylcone to the flap. (not in situ), it does seem a little loose.. as if the seal has stretched.
If this seal has gone, would this allow dust up the inside centre section of the cyclone, and if so, could this also be part of my problem ?
In the short term, I’ve duck taped the cracks over until we decide whether to fix or replace.
I’ve found the cost of the trap door, unfortunately, not on this site.
Is the seal called “Fine Dust Collector Seal”Re: Dydon DC08 pre filter cleaning
Sorry.. a slight typo.. it is in fact a DC07.
I initailly tried giving the cyclone section a good shake rattle and roll in the bin..I’ll get my car vac on it and try this..failing that, what’s the next options.. considering it’s a sealed unit ?
buy another cyclone ??
dump the vac for a new one ??You say not to try and wash it out.. but as a last resort.. what about an over night soak.. is there anything inside the cyclone that could be damaged by soaking ??
It’s not much use as it is, having to wash the filer out every week, so we have very little to lose !!
Re: Gorenje auto WA50140
Hi Brian,
Gorenje.co.uk – Select Laundry and click on the Model you require. Lower down the page there is a tab ‘Enclosure’. Click this tab and you will see a download pdf file – ‘Instructions for use’.
HTH.
Richard
