allan73

Forum Replies Created

Viewing 15 posts - 61 through 75 (of 497 total)
1 2 3 4 5 6 … 32 33 34
  • Author
    Posts
  • March 20, 2014 at 12:00 pm in reply to: AEG dishwasher pnc 91193861013 i60 fault #411322
    allan73
    Participant

    Re: AEG dishwasher pnc 91193861013 i60 fault

    Been out to this today. No visual signs of a problem on the board, water sits just under an inch above the filter and heater still works.
    Where would the NTC be located on this ?
    Allan

    February 18, 2014 at 8:54 pm in reply to: Neff S5453X1GB/50 No Start #409950
    allan73
    Participant

    Re: Neff S5453X1GB/50 No Start

    Yes I get your point Matin. I’ll speak to the customer about going back tomorrow.
    Allan

    February 18, 2014 at 8:43 pm in reply to: Neff S5453X1GB/50 No Start #409948
    allan73
    Participant

    Re: Neff S5453X1GB/50 No Start

    Haven’t tried to be honest Martin. What would that indicate ?
    Allan

    February 12, 2014 at 10:22 am in reply to: Siemens SN26M830GB/25 aborts half way through #409422
    allan73
    Participant

    Re: Siemens SN26M830GB/25 aborts half way through

    Is it common for the reed switch to fail part way into a cycle ?
    Allan

    February 12, 2014 at 8:17 am in reply to: Siemens SN26M830GB/25 aborts half way through #409421
    allan73
    Participant

    Re: Siemens SN26M830GB/25 aborts half way through

    Thanks Martin, you succeeded where Qualtex tech dept failed.
    Allan

    February 2, 2014 at 9:14 am in reply to: Prima LPR 601 (Whirpool) dishwasher no circ pump #408748
    allan73
    Participant

    Re: Prima LPR 601 (Whirpool) dishwasher no circ pump

    Thanks Steve, I recall having a problem after changing a heater on one of these. Motor should have been changed also serial no dependant apparently, so I take what you say on board.

    Allan

    January 31, 2014 at 4:10 pm in reply to: Hoover HNL2126 cuts out on spin #408619
    allan73
    Participant

    Re: Hoover HNL2126 cuts out on spin

    Thanks Martin I’ll check all the relevant connections.
    Allan

    December 6, 2013 at 10:39 pm in reply to: Hotpoint’s not draining #387194
    allan73
    Participant

    Re: Hotpoint’s not draining

    Interesting…that’s exactly the problem, thanks A1 !
    Allan

    December 6, 2013 at 10:19 pm in reply to: Hotpoint’s not draining #387192
    allan73
    Participant

    Re: Hotpoint’s not draining

    Would the NTC stop the pump from being energised ?
    The machine will fill, wash and spin when emptied manually.
    Allan

    December 6, 2013 at 3:57 pm in reply to: Hotpoint’s not draining #387190
    allan73
    Participant

    Re: Hotpoint’s not draining

    Thanks I’ll speak to the customer.
    Allan

    December 6, 2013 at 2:46 pm in reply to: Hotpoint’s not draining #387188
    allan73
    Participant

    Re: Hotpoint’s not draining

    Thanks Tim. I have tried to reset the pressure switch also, to no avail.
    Allan

    December 6, 2013 at 11:54 am in reply to: Hotpoint’s not draining #387186
    allan73
    Participant

    Re: Hotpoint’s not draining

    Did you get to the bottom of this one Iadom ?
    I’ve got one of these with the same fault. Customer has removed a hair grip from the filter so I’m wondering if board damage has occurred.
    Allan

    November 5, 2013 at 5:19 pm in reply to: Hpt VTD00 S/n 511281742 inner door rim #404034
    allan73
    Participant

    Re: Hpt VTD00 S/n 511281742 inner door rim

    Thanks Iadom.

    November 5, 2013 at 1:52 pm in reply to: Di 620uk not selecting programme #403936
    allan73
    Participant

    Re: Di 620uk not selecting programme

    Thanks for the advise Jem.
    I’m off to the Highlands in the morning so I’ll have to deal with it when I get back.
    Allan

    November 5, 2013 at 12:01 pm in reply to: Di 620uk not selecting programme #403934
    allan73
    Participant

    Re: Di 620uk not selecting programme

    I take it these caps are a pig to change ?

  • Author
    Posts
Viewing 15 posts - 61 through 75 (of 497 total)
1 2 3 4 5 6 … 32 33 34