Forum Replies Created
-
Posts
-
Re: Leaking Indesit dishwashers. Is there a technical bulle
yes Quiet correct it stops pressure build up and cures leaking from left and right side of tank adjacent to door hinges , Cut main door seal length to 5mm below door seal retainer. Hope this helps
Re: Hotpoint CDT80/85
F01 Motor triac in short circuit or
Relay of motor welded
closed.
– Verify if moisture has made a short circuit on connector J3;
– Verify if the motor connectors on board are ok. (Problems of
aggressive chemicals can generate a short circuit.)
– Change the board.
F02 Blocked motor. (Fan
blocked)
– Verify if the motor / fan is blocked;
– Verify the J3 connectors on the board;
– Replace motor;
– Replace fan;
– Replace main board.
F03 Front NTC open or short
circuit.
– Verify efficiency of the J12 connector on the board;
– Verify NTC on J12 connector, the value at Room temperature
of the NTC must be around 500 KΩ;
– If the measurement is out of range verify continuity of wiring
and verify directly on NTC without wiring;
– Replace NTC;
– Replace main board.
F04 No pump connection.,
feedback.
– Verify efficiency of contact J5;
– Verify wiring J5/Pump;
– Verify pump;
– Replace pump;
– Replace main board.
F05 No feedback from the pump. – Verify contact efficiency of J5 connector of the board;
– Verify if tension getting at the pump;
– Verify pump;
– Replace pump;
– Replace main board.
F06 Non used, active –
F07 Non used, active –
F08 Static heater Relay with NA/
NC contact welded closed
– Verify efficiency of contact J4;
– Verify at room temperature on the J4 connector if the
resistance between Pin 1 and 2 is 48 Ω;
– Verify continuity between wiring between J4 and Static (lower)
Heater;
– Replace Heater;
– Replace main board.
F09 Error set up file. EEEPROM
is not programmed or not
functioning.
– If it is a production board with welded EEPROM, replace
board;
– If it is a board with removable EEPROM, check the correct
positioning of the EEPROM.
F10 Common of heater open,
one shot open.
– Verify efficiency of contact J4;
– Verify at room temperature (20°C) on the J4 connector if the
resistance between Pin 1 and 2 is 48 Ω;
– Verify continuity between wiring between J4 and Static (lower)
Heater;
– Replace Heater;
– Replace main board.
F11 No pump connection. – Verify efficiency of board contact J5;
– Verify wiring between J5 connector and pump.
– Replace pump;
– Replace board.
F12 No communication between
display board and control
board.
– Verify contact efficiency of board connector J9;
– Verify continuity between J9 and 5 leads connector of the
display board;
– Replace main board;
– Replace display board.
F13 Rear NTC open or short
circuit.
– Verify efficiency of J4 connector on main board;
– Verify at room temperature (20°C) is about 500KΩ;
– Verify continuity of wiring between J4 and NTC rear;
– If the measurement is out of range verify continuity of wiring
and verify directly on NTC without wiring;
– Replace NTC;
– Replace main board.
F14 Not used, active –
F15 Dynamic (PD) heater Relay
with NA/NC contact welded
closed.
– Verify efficiency of contact J4;
– Verify at room temperature (20°C) on the J4 connector if the
resistance between Pin 1 and 2 is 48 Ω;
– Verify continuity between wiring between J4 and Static Heater;
– Replace Heater;
– Replace main board.
F16 Not used, active –
F17 Master Relay welded closed – Replace main boardRe: WMA30
i would quiz customer about the load . as it is possible that it has had an out of balance load thus reverting back to distribute several times and increasing the wash cycle by up to 15 mins before giving up trying to balance the bath mat and pair of wellies she is trying to wash.
Re: H/Point BWM12 – Timer knob
the only way to remove main timer knob on these machines is to drill a hole in centre to access the retaining screw then replace with c00087814 .
Re: Indesit tech
you will find that if it an origional module the eeprom will be soldered on so you will need both module and eeprom. Module c00093157 and eeprom c00094742 if the machine is fitted with plastic tank and c00089846 if fitted with metal tank . if the machine has had the module replaced in the past then it will be fitted with a service module which has a removable eeprom and possibly get away with just the eeprom. Good LUCK
Re: Indesit/Ariston modules… Can they be replaced
with reguards to the difference between boards with removable epproms and soldered eeproms .All machines are produced wit a soldered eeprom and all service replacement modules come without an eeprom fitted so if you aint seen one with a removable eeprom then it is the origonal module
Re: Hotpoint WMA32
the plugs are all keyed and will only fit in correct place . as for the two single wires the one with the shield go to the right spade and the unshielded goes to the left (towards centre of board ) if you need diagram pm me and i will mail it you
Re: Hotpoint BWM20 Integrated WM.
it is an ariston built machine , door seals ar not a bad job to do . i tend to poke a long screwdriver through interlock hol to aid refitting inner retaining spring , other than that straight forward 5 minuite job
Re: Hotpoint WF860P
Comet are no longer buying out gtees , the in guarantee work reverted back to hotpoint about 3 months ago . 😀
