Allsorts

Forum Replies Created

Viewing 15 posts - 556 through 570 (of 1,356 total)
1 2 3 … 37 38 39 … 89 90 91
  • Author
    Posts
  • April 2, 2012 at 5:09 pm in reply to: the Associate member question #372666
    Allsorts
    Participant

    Re: the Associate member question

    If you are going to ask for a vote on it (which I don’t think you should request a vote; you would not normally vote on a security issue), then be sure to describe the full tier structure so that the reason is fully visable.

    Also describe the possible flaws if the addendum where not placed into the constitution.

    George

    March 25, 2012 at 7:37 pm in reply to: Hoover/Candy new control units #372030
    Allsorts
    Participant

    Re: Hoover/Candy new control units

    Already done reports back to currys on some of these who are supplying new controllers.

    March 25, 2012 at 12:27 pm in reply to: Hoover AC110 heating problem #371364
    Allsorts
    Participant

    Re: Hoover AC110 heating problem

    Are you sure it was heating before your repairs… The element could be at fault, or other items.

    March 23, 2012 at 8:03 am in reply to: LAMONA SPARES #371939
    Allsorts
    Participant

    Re: LAMONA SPARES

    If they dont actually have them will know where to order them. They will be the best source of knowledge.

    It’ll also depend on the machine, Lamona use Beko, Stoves, and a few others to build their appliances.

    😀

    March 23, 2012 at 7:34 am in reply to: LAMONA SPARES #371937
    Allsorts
    Participant

    Re: LAMONA SPARES

    Ring Howdens

    March 21, 2012 at 4:50 pm in reply to: Zanussi ZWD16270 Service #371439
    Allsorts
    Participant

    Re: Zanussi ZWD16270 Service

    Thanks Mike, I’ll have a gander at it and see what comes.

    regards
    George

    March 20, 2012 at 10:42 am in reply to: ISE aw23 water not heating up #371396
    Allsorts
    Participant

    Re: ISE aw23 water not heating up

    The washing would normally come out of the machine cold after a rinse.

    March 15, 2012 at 7:48 am in reply to: Hotpoint WT960 F-02 #371110
    Allsorts
    Participant

    Re: Hotpoint WT960 F-02

    Think this is one of the 3-phase models

    March 14, 2012 at 8:48 am in reply to: AEG Washing Machine Approx 2-3 years old #362516
    Allsorts
    Participant

    Re: AEG Washing Machine Approx 2-3 years old

    Wouldlike to know what you find on this… I have one here doing the same thing.

    March 13, 2012 at 8:52 pm in reply to: Capacitor Discharge Leads – for Microwave use #370891
    Allsorts
    Participant

    Re: Capacitor Discharge Leads – for Microwave use

    Martin wrote:

    BobHope wrote:
    Use the discharge probe on each side of the capacitor in turn for a second or two, Since the time constant RC is about .1 second, this should drain the charge quickly and safely

    I thought that clip was to be put on the chassis of the microwave… the same way we used to discharge the tube of a CRT TV. Good job I don’t meddle with microwaves isn’t it.

    George

    March 13, 2012 at 11:55 am in reply to: Servis M2010 tumble dryer #370953
    Allsorts
    Participant

    Re: Servis M2010 tumble dryer

    Martin,

    What is the drum state when the belt isd off… is it still tight?

    George

    March 13, 2012 at 8:40 am in reply to: Washing Machine Tripping Electrics #370028
    Allsorts
    Participant

    Re: Washing Machine Tripping Electrics

    I would be looking at the cable or the suppressor…

    Check for breaks in the cable either on the outside insulation or inside the plug…
    Remove the plug from the wall, remove the lid and look for damage, burnmarks or breaks on or nearby the mains supressor.

    March 13, 2012 at 8:23 am in reply to: Whirlpool APDW 12 stuck near beginning of cycle #370802
    Allsorts
    Participant

    Re: Whirlpool APDW 12 stuck near beginning of cycle

    That is possibly Whirlpool APDW/2

    If the pump is not jammed but gone then the part would be
    481236158434 – Whirlpool & Others Dishwasher Motor

    George

    March 13, 2012 at 8:05 am in reply to: HEC 1050W – Module #370893
    Allsorts
    Participant

    Re: HEC 1050W – Module

    Haier Control Module HEC1050

    George

    March 13, 2012 at 8:01 am in reply to: Hotpoing Aqualtis 1600 8kg – Weird problem with pump #370937
    Allsorts
    Participant

    Re: Hotpoing Aqualtis 1600 8kg – Weird problem with pump

    First question… what is the model number

  • Author
    Posts
Viewing 15 posts - 556 through 570 (of 1,356 total)
1 2 3 … 37 38 39 … 89 90 91