Forum Replies Created
-
AuthorPosts
-
aqua_serve
ParticipantRe: Diplomat ADP8322 circulation pump.
Thanks Colin 🙂
aqua_serve
ParticipantRe: Hoover VHV180-80
Thanks for the opinion 🙂
aqua_serve
ParticipantRe: Hoover VHV180-80
Cheers Martin, you’re a star!
Just as confirmation would you agree with my diagnosis?
Mark
aqua_serve
ParticipantRe: Zanussi ZWF1440W in a spin
Thanks for the pointers. I’m goiong to head down later to give it a shot! I’ll keep you posted 🙂
Mark
aqua_serve
ParticipantRe: Zanussi ZWF1440W in a spin
Further to my last post I went to the property today to have another look at the machine. Looks like this is going to be one to cut my teeth on in a way.
The customer it appears has never been happy with the machine, even though it’s only 3 years old they have had a new motor under warranty, a new door seal and issues with conditioner not releasing into the drum. She told me they are opting for a new machine.
I’d still like to solve the problem in the hope it will enlighten me a little more to Zanussi and their diagnostics.
During today’s visit I put it into the test mode, what I wasn’t so sure abbout was how long you’re meant to leave the machine in each section of the test before moving the selector on? I tried it today leaving each section of the test for about a minute before moving to the next stage.
I did obtain an error message ‘E32’ which according to the bible is an inconsistency between the electronic pressure switch and anti-boiling pressure switch.
Without wanting to spend any time on the machine without some advice from you all does this sound like a reasonable explaination as to why the machine is doing what it’s doing?
Both before and after the test mode I tried the spin and on cue it set itself to 10 minutes, door locks, pump operates, 6-7 seconds later the 1400 and spin leds go out the pump stops, door opens and the display shows 0.
It’s basically a machine to learn on but would love to zap it for my own pride, plus the customer might be able to pass it on.
Mark
aqua_serve
ParticipantRe: Zanussi ZWF1440W in a spin
No and that is an oversight on my part, thanks. Will venture down tomorrow. Not at home at the moment, the details are in the fault code booklet for this one aren’t they?
Mark
aqua_serve
ParticipantRe: Zanussi TD4112W
Colin, a wiring diagram would be great if you have one to hand.
Yours,
Mark
aqua_serve
ParticipantRe: Zanussi ZWF1440W
Dave,
They look like the ones.
Many thanks,
Mark
aqua_serve
ParticipantRe: LG WM1437BFD washing machine.
John,
Thanks for the post, I’ve tried to PM you put can’t seem to work out why they aren’t sending!
My email address is mark_r_ryan@hotmail.com
Mark
aqua_serve
ParticipantRe: LG WM1437BFD washing machine.
I was thinking so! Thanks for the confirmation. Is it quite straight forward??
I’m also trying to get the machine to just go into spin mode (this doesn’t have one on the program selector) is there any way of doing this, is there a test mode for this series of machine? I was hoping a service manual would shed light on it
Mark
aqua_serve
ParticipantRe: Baumatic BT2460SS element
Thanks for the reply, I go with you on the brand, sad you have to pay through the nose for an element though!
aqua_serve
ParticipantRe: Electrolux ESL6225 dishwasher
Colin,
Thanks for the reply, I’ll check, the leak seems to occur after the machine initially fills (after about 10 seconds) could this still be the case?
Mark
aqua_serve
ParticipantRe: Door handle for Hoover OPH616-80
Many thanks, you’re a star!
aqua_serve
ParticipantRe: Ariston a1636 Washing Machine
Cheers Jim
This one was really getting on my nerves, I was trying to drain the machine after cancelling the program only to find it went into a prewash cycle filling even more!!!
Looks like Connect are out of the part.
Will keep you all posted.
Mark
aqua_serve
ParticipantRe: Ariston a1636 Washing Machine
Sorry for the late response to the previous posts, fitted the replacement module the other day (EMW reported a fault on it). All looked good until I selected a cycle. The door locked and cycel started – the problem is that it was the wrong cycle, for example after choosing a wash cylce the prewash LED lights and the machine appears to start a prewash cycle.
Cancelling the program stops the machine but then after selecting ‘drain’ it is hit and miss as to whether or not it will drain or go to a prewash or wash program. All very confusing and iritating.
I contacted EMW who requested I sent the control board and module back, this was returned working – infact they kindly changed the control board to give me piece of mind.
Can any of you advice me as to where I need to be looking? Would I be right in thinking when the module carked it it might have taken the program selector with it?
I’m really scratching my head on this one.
Mark
-
AuthorPosts
