bazza500

Forum Replies Created

Viewing 15 posts - 121 through 135 (of 1,916 total)
1 2 3 … 8 9 10 … 126 127 128
  • Author
    Posts
  • March 1, 2016 at 8:47 pm in reply to: Beko drcs68w Mains Filter #435929
    bazza500
    Participant

    Re: Beko drcs68w Mains Filter

    They just pop. Fit a replacement and it’ll be fine.

    February 22, 2016 at 6:16 pm in reply to: Beko WMB91442LW #435635
    bazza500
    Participant

    Re: Beko WMB91442LW

    Belt slipping?

    February 22, 2016 at 6:15 pm in reply to: One off opportunity. #435658
    bazza500
    Participant

    Re: One off opportunity.

    It would have to be enough to retire abroad straight after airing.

    February 18, 2016 at 7:58 pm in reply to: Gorenje F/F Thermostat #435468
    bazza500
    Participant

    Re: Gorenje F/F Thermostat

    596249

    February 16, 2016 at 10:59 pm in reply to: Servis Caress 1200A M3102A #435425
    bazza500
    Participant

    Re: Servis Caress 1200A M3102A

    Pressure tube blocked and the machine already thinks it’s full.

    February 8, 2016 at 2:05 pm in reply to: Zanussi ZDT12011FA Pump running continuously #435180
    bazza500
    Participant

    Re: Zanussi ZDT12011FA Pump running continuously

    The water will not leak out of the machine it will stay in the base so you wont see it without taking panels off. Did all the water pump away or did some of it leak into the base? That is the question.

    February 8, 2016 at 1:21 pm in reply to: Zanussi ZDT12011FA Pump running continuously #435178
    bazza500
    Participant

    Re: Zanussi ZDT12011FA Pump running continuously

    Sounds like you have a leak which has flooded the base. Tip the dishwasher slightly to the side and see if any water runs out.

    January 29, 2016 at 2:51 pm in reply to: Beko DSC85W Facia panel #434851
    bazza500
    Participant

    Re: Beko DSC85W Facia panel

    2982309004

    January 27, 2016 at 8:37 am in reply to: Kenwood fridge freezer #434808
    bazza500
    Participant

    Re: Kenwood fridge freezer

    Isn’t “ES” energy saving mode? Should mention it your manual if it is.

    January 24, 2016 at 10:01 pm in reply to: Is it legal to fit 13amp sockets #434656
    bazza500
    Participant

    Re: Is it legal to fit 13amp sockets

    Martin, one minute your post are all high and mighty and “you must abide by the rules”, the next your all “never mind abiding by the rules as long as you’re close”.


    C’mon man , make up your mind!

    January 17, 2016 at 1:19 pm in reply to: AEG L1451 Washing machine E40 Door Lock #434535
    bazza500
    Participant

    Re: AEG L1451 Washing machine E40 Door Lock

    Have you ran the diagnostics to see what fault code you get?

    January 11, 2016 at 5:57 pm in reply to: aeg f34502v10 dw 91153911400 #434414
    bazza500
    Participant

    Re: aeg f34502v10 dw 91153911400

    This DW just has the heater and the circulation pump as one unit. Nothing special, you can still check the heater continuity so see if it’s faulty.

    December 30, 2015 at 2:28 pm in reply to: Repairtech (UK) Ltd – Is this a joke? #434117
    bazza500
    Participant

    Re: Repairtech (UK) Ltd – Is this a joke?

    I emailed back declining that offer approximately 0.000001 millisecond after the email arrived. I have no idea what the Repairtech team were drinking when they thought that was a good idea but I wouldn’t mind some of it for the New Year.

    December 28, 2015 at 1:35 am in reply to: AEG Favorit 34502VIO (911 539 114 00) #423052
    bazza500
    Participant

    Re: AEG Favorit 34502VIO (911 539 114 00)

    This machine probably needs the pressure switch modification done.

    December 23, 2015 at 9:42 pm in reply to: Rangemaster 110 induction #434000
    bazza500
    Participant

    Re: Rangemaster 110 induction

    Dead easy. Undo 2 screws on the side at the front in behind rubber grommets. Undo 2 screws on the rear hinges and lift up.

  • Author
    Posts
Viewing 15 posts - 121 through 135 (of 1,916 total)
1 2 3 … 8 9 10 … 126 127 128