clockworkone

Forum Replies Created

Viewing 15 posts - 136 through 150 (of 555 total)
1 2 3 … 9 10 11 … 35 36 37
  • Author
    Posts
  • May 27, 2016 at 7:46 am in reply to: fdw20 no heat #437956
    clockworkone
    Participant

    Re: fdw20 no heat

    Yes Jim I found it strange not to have 2nd and 4th light flashing to indicate board or heater. Thinking about it afterwards I was wondering would it be the high pressure sensor that has failed. Will complete a cycle. Machine fills to correct level. Why are friends machines always the awkward ones. Thank you for reply and part no.

    May 23, 2016 at 5:00 pm in reply to: whirlpool reeds #437607
    clockworkone
    Participant

    Re: whirlpool reeds

    Sorry for late reply Don. The item I’m after are the little glass reed switches that you solder onto small board on side of fill matrix on whirlpool dishwashers. Failure of these throws up the f7 fault. I know you can buy the little board already made up,but these are an easy repair and are cheap to buy in bulk off Rs electronics. Thanks again for replying.

    May 5, 2016 at 7:44 am in reply to: Beko d/w module #437479
    clockworkone
    Participant

    Re: Beko d/w module

    Thanks very much Dave.

    April 8, 2016 at 8:11 am in reply to: Flavel oven seal #436874
    clockworkone
    Participant

    Re: Flavel oven seal

    Thank you very much for all the help.

    February 23, 2016 at 4:32 pm in reply to: Whirlpool azc 6470 #435702
    clockworkone
    Participant

    Re: Whirlpool azc 6470

    Thank you Don.

    January 28, 2016 at 9:18 am in reply to: hotpoint/indesit dryer recall #434824
    clockworkone
    Participant

    Re: hotpoint/indesit dryer recall

    Thank you Don and Martin for reply. Not sure how well the word “Mainland” fitted into the conversation though Don as we both live in separate countries.Paul

    :tup:

    December 16, 2015 at 2:01 pm in reply to: rangemaster 110/odf adl #433837
    clockworkone
    Participant

    Re: rangemaster 110/odf adl

    Sorry I realised after I posted it that I had forgotten mod no. You must have replied as I was editing it. My mistake. 050564085.

    December 12, 2015 at 9:09 am in reply to: E/lux Eob5700x oven toc #433630
    clockworkone
    Participant

    Re: E/lux Eob5700x oven toc

    Thank you Don

    December 8, 2015 at 9:36 pm in reply to: Zanussi ZWHB7160 cannot open filter in drum #433498
    clockworkone
    Participant

    Re: Zanussi ZWHB7160 cannot open filter in drum

    Bernie I would be grateful for a copy of this manual as I have one to look at soon. email is appliancerepairs1@eircom.net

    November 4, 2015 at 8:15 am in reply to: zwg6141p #432157
    clockworkone
    Participant

    Re: zwg6141p

    Many thanks for replies. Can see shaft turning at rear of control panel. Will take board out and bring into guy that does any electronics for me.

    October 27, 2015 at 12:50 pm in reply to: Bosch wae2416gb/03 #431851
    clockworkone
    Participant

    Re: Bosch wae2416gb/03

    Thank you Martin. Motor connector plug on module burnt out.

    October 15, 2015 at 9:37 pm in reply to: wma48 no spin #431008
    clockworkone
    Participant

    Re: wma48 no spin

    Thank you Jim.

    October 7, 2015 at 7:30 am in reply to: Hoover washer WMH139D – unintelligible flashing display #430746
    clockworkone
    Participant

    Re: Hoover washer WMH139D – unintelligible flashing display

    Selector switch. Switch on machine. Tap control knob lightly to see if display flickers.

    October 5, 2015 at 8:06 am in reply to: Belling idw704 module #430733
    clockworkone
    Participant

    Re: Belling idw704 module

    Thank you Steve.

    August 21, 2015 at 8:45 am in reply to: siemens w/machine e61 and e35 #429662
    clockworkone
    Participant

    Re: siemens w/machine e61 and e35

    Fitted new interlock. Ran 15 min wash,all good. Would be great to get error codes and diag for these as they are quite popular around here now.

  • Author
    Posts
Viewing 15 posts - 136 through 150 (of 555 total)
1 2 3 … 9 10 11 … 35 36 37