clockworkone

Forum Replies Created

Viewing 15 posts - 436 through 450 (of 555 total)
1 2 3 … 29 30 31 … 35 36 37
  • Author
    Posts
  • July 20, 2011 at 8:17 am in reply to: whirlpool heater #355810
    clockworkone
    Participant

    Re: whirlpool heater

    thank you john.paul

    July 15, 2011 at 8:03 am in reply to: zanussi impeller kit #355594
    clockworkone
    Participant

    Re: zanussi impeller kit

    thank you keith.

    July 13, 2011 at 10:24 pm in reply to: creda oven #355503
    clockworkone
    Participant

    Re: creda oven

    many thanks for that jim,sorry about typo on e mail add.thanks again. paul

    July 13, 2011 at 9:43 pm in reply to: creda oven #355501
    clockworkone
    Participant

    Re: creda oven

    anyone got wiring diag. email add is apliancerepairs1@eircom.net

    June 26, 2011 at 10:06 am in reply to: whirlpool washers AWO/D series #354198
    clockworkone
    Participant

    Re: whirlpool washers AWO/D series

    hi micky32 any chance you could forward this manual to me as well,have one to look at this week.have sent pm with email address.

    June 21, 2011 at 4:35 pm in reply to: zwf10020w #353931
    clockworkone
    Participant

    Re: zwf10020w

    thanks martin, i did check connections at both ends and all looked good,will stick heater in and see how it goes.cant believe i didnt check ntc readings when i disconnected it :clown: thanks again.paul

    June 15, 2011 at 5:17 pm in reply to: 680u-10v capacitors #353603
    clockworkone
    Participant

    Re: 680u-10v capacitors

    thank you Don.

    June 9, 2011 at 3:07 pm in reply to: whirlpool top loader 3rgsc9455 #353248
    clockworkone
    Participant

    Re: whirlpool top loader 3rgsc9455

    thanks for that dave.was at this one today.fuse was good and put a jumper in lid switch once cabinet off.capacitor was in bits so changed that.checked pump and that was clear.rubber joiner between motor and gearbox ok. tested machine with cabinet off and every thing was good.put cabinet back on connected lid sw and tried again and no motor action and smoke(coincidence).shaft very hard to turn so suspect corrosion between spin tube and drive shaft.customer not willing to spend money on it so left it at that.machine used solely for horse rugs and has had a hard life i would say

    June 7, 2011 at 9:10 am in reply to: tactile switch #352901
    clockworkone
    Participant

    Re: tactile switch

    thanks dave and martin.due to my location i dont have a shop near me to get these.i understand about taking off old boards but i remember on a post a while ago someone mentioned they carry around a bag of these switches with them.i will try and track down the author of this and see can i get a number off them.thanks again.paul

    June 3, 2011 at 2:55 pm in reply to: w/m model no please if possible #352810
    clockworkone
    Participant

    Re: w/m model no please if possible

    thanks john appreciate that.

    June 2, 2011 at 5:00 pm in reply to: stoves range style cooker #352704
    clockworkone
    Participant

    Re: stoves range style cooker

    just an update sorted now.

    June 1, 2011 at 8:20 pm in reply to: hoover hnf6127-80 #352629
    clockworkone
    Participant

    Re: hoover hnf6127-80

    thanks for that barrie.

    May 29, 2011 at 5:54 pm in reply to: stoves dual fuel grill regulator replacement #351645
    clockworkone
    Participant

    Re: stoves dual fuel grill regulator replacement

    thank you for that seamy.

    May 27, 2011 at 10:27 pm in reply to: stoves dual fuel grill regulator replacement #351643
    clockworkone
    Participant

    Re: stoves cooker 1200dfa

    does anyone have any tech info on this one.struggling a bit with this one.

    May 26, 2011 at 8:47 pm in reply to: wf101 tripping #352072
    clockworkone
    Participant

    Re: wf101 tripping

    ok no prob

  • Author
    Posts
Viewing 15 posts - 436 through 450 (of 555 total)
1 2 3 … 29 30 31 … 35 36 37