[conormccleane]

Re: Bosch SGS43T02GB/06 D/W Help

Hi,
Anyone got an idea on this?????????
Thanks,
Conor!

[conormccleane]

Re: Miele W3240 – Too much detergent error.

Thanks guys,
Appreciate the feedback. Will call customer and advise.
Conor!

[conormccleane]

Re: Miele G7859

“F2E – When water intake has not been completed within the overriding time control of 5 mins, the program is interrupted”

If the hot supply is intermittent this can knock the machine out – use a y-piece and put hot and cold hoses off the cold supply only. Normally though, if you get an F1E, F2E or F3E and the water supply is OK and filters are clean, I normally change out the heating level control switch – part nr 4441514.
Cheers!

[conormccleane]

Re: Bosch SGV53E03GB/50 No heat

Thanks nomad,
All check out ok. I did notice a lot of suds in the cabinet, rinse aid I suspect. Flushed through a few times and mopped out. Heating ok now – must ask customer if she spilled rinse aid in cabinet – that might explain tripping RCD’s.
Regards,
Conor! 😀

[conormccleane]

Re: Miele PW5065 Poor Spin Performance

Thanks for the replies,
Checked out the fault memory on the machine and deleted it – don’t know how long they have been on machine – will call back this week to see what new faults if any have been logged. Faults logged were:
F47 – BAE/SLT Interface Defective
F39 – Vacant
F11 – Water Drainage
F16 – Foam/Excess Detergent
F50 – Drive
F15 – Water Intake Fault – Hot

What is a BAE/SLT Interface? and what does an F50 – Drive fault suggest?
Conor!

[conormccleane]

Re: Bosch FD8811 WAE24467 Washer F18 Fault

Thanks Paul,
Customer runs a riding school – saw lots of horse hair in drain standpipe and at end of drain hose. Sump and pump OK – will call back and check drain hose.
Conor!

[conormccleane]

Re: Whirlpool Dishwasher ADG7460 (8511 440 15880)

Thanks Franz,
BER I’d say – I can’t vouch for the cabinet alignment.
Conor!

[conormccleane]

Re: Whirlpool AWO/D 4505 859233215000

PS Is this door lock mechanical or electronic in operation? I ask because when disassembled I couldn’t see anything mechanical in its operation.
Ta very much!!!

[conormccleane]

Re: Whirlpool Dryer AWZ 3303

Belt ok; no obstructions on rollers; BTW any guide available on checking motor windings etc.

[conormccleane]

Re: Whirlpool Dryer AWZ 3303

Just to add that the capacitor seems ok and the service number is 8575 330 15033;
Conor!

[conormccleane]

Re: Siemens WM12E468GB/07 F63 fault

Thanks Gerry; one question though, how do I enter the test mode?
Conor!

[conormccleane]

Re: Zanussi IZ12 Washer E90 fault

will try later and advise – many thanks…

[conormccleane]

Re: Neff Dishwasher not taking in enough water

Sump hose blocked/cleared. Hopefully this should sort prob.
Conor!

[conormccleane]

Re: Powerpoint TW36FI

Hi. Have a powerpoint TW36FI and powers up ok but I cannot select a program. Only the salt LED comes on. Any ideas please.
Conor!

[conormccleane]

Re: Commercial Zanussi Oven – no steam generation

Thanks,
I’ll have a quick look later.
Conor!

[Author]

Posts