DentedPorsche

Forum Replies Created

Viewing 15 posts - 376 through 390 (of 915 total)
1 2 3 … 25 26 27 … 59 60 61
  • Author
    Posts
  • June 3, 2007 at 7:48 pm in reply to: fault codes pdf #212257
    DentedPorsche
    Participant

    Re: fault codes pdf

    and not to be left out 😛

    May I have a copy too?

    dentedporsche@hotmail.com

    Thanks
    Brian

    May 31, 2007 at 5:53 pm in reply to: Whirlpool AWZ541 fan probs? #215575
    DentedPorsche
    Participant

    Re: Whirlpool AWZ541 fan probs?

    Did you release the front of the machine? Normally have to release the front panel to get the ducting back on.

    Brian

    May 31, 2007 at 6:26 am in reply to: Prima LPR 600 (854560015810) #215466
    DentedPorsche
    Participant

    Re: Prima LPR 600 (854560015810)

    If it’s not listed on the Whirlpool site you have to request it. There should be a link in the manuals section for that along with instructions.

    DP

    May 31, 2007 at 5:53 am in reply to: British Gas To Drop Appliance Servicing? #162365
    DentedPorsche
    Participant

    Re: British Gas To Drop Appliance Servicing?

    Posting removed at the request of BG engineer.

    May 21, 2007 at 6:10 pm in reply to: Hotpoint CTD40 #214399
    DentedPorsche
    Participant

    Re: Hotpoint CTD40

    One in the middle is an NTC, had one a few weeks back. 🙁

    Brian

    May 11, 2007 at 5:47 am in reply to: Whirlpool American Fridge Freezer broken down – help! #141928
    DentedPorsche
    Participant

    Re: Whirlpool American Fridge Freezer broken down – help!

    If you know what’s wrong with the boards then yes you can repair them.
    Some have managed to repair them, others have had no luck.
    Best place to buy replacements is to click on Shop@ on the left side of this page.

    DP

    May 10, 2007 at 7:23 pm in reply to: Whirlpool American Fridge Freezer broken down – help! #141926
    DentedPorsche
    Participant

    Re: Whirlpool American Fridge Freezer broken down – help!

    You’ve got the older electronics so both boards required.

    DP

    May 10, 2007 at 7:20 pm in reply to: whirpool temperature broken #213110
    DentedPorsche
    Participant

    Re: whirpool temperature broken

    Was the freezer display flashing – – ?
    How long between the meter running out and power being restored?
    It sounds like the evaperator may be blocked.


    DP

    May 10, 2007 at 7:13 pm in reply to: Ikea DWF B10W Constant Bleeping and Flashing Start Light #212768
    DentedPorsche
    Participant

    Re: Ikea DWF B10W Constant Bleeping and Flashing Start Light

    Base is flooded, likely leaking, and circulation motor is getting wet.
    Drain the base (not inside the machine, below that) and try again checking for a leak into the base.

    DP

    May 10, 2007 at 7:10 pm in reply to: smeg slimline dishwasher dead #213199
    DentedPorsche
    Participant

    Re: smeg slimline dishwasher dead

    Take the module out and check the underside, you’ll probably find where it’s blown.

    Brian

    May 10, 2007 at 7:09 pm in reply to: Diplomat ADP8332 #213103
    DentedPorsche
    Participant

    Re: Diplomat ADP8332

    If it works when it’s pulled out but fails when it’s pushed back into place I’d suspect the fill hose is being kinked, thereby cutting the water supply either partially or completely.

    Brian

    May 10, 2007 at 7:05 pm in reply to: diplomat adp8322 #213276
    DentedPorsche
    Participant

    Re: diplomat adp8322

    Check the known error codes, page 2, Whirlpool.
    The flashing light is an error code and on any fault it reverts to rinse setting.

    Brian

    May 9, 2007 at 4:38 pm in reply to: Zanussi Tumble Drier TC7102W #213153
    DentedPorsche
    Participant

    Re: Zanussi Tumble Drier TC7102W

    Already thought of that one 🙁
    The only change is the garage, machine has always been there but now it’s a proper room instead of bare walled.

    Brian

    May 9, 2007 at 3:19 pm in reply to: Diplomat ADP8332 #213101
    DentedPorsche
    Participant

    Re: Diplomat ADP8332

    Nope.
    Flow meter is embedded in the water matrix, left hand side at the bottom. Normal fault is bad connection.
    Water indicator is under the mesh filter, in the bowl area at 3 o’clock position.
    F7 can be one of several possibilities, check the known fault codes for full info.

    Brian

    May 3, 2007 at 5:56 pm in reply to: W/Pool F/F #212661
    DentedPorsche
    Participant

    Re: W/Pool F/F

    It’s self sealing.

    Brian

  • Author
    Posts
Viewing 15 posts - 376 through 390 (of 915 total)
1 2 3 … 25 26 27 … 59 60 61