eastlmark

Forum Replies Created

Viewing 15 posts - 1,651 through 1,665 (of 4,480 total)
  • Author
    Posts
  • in reply to: Matsui MFi60 rusting #311124
    eastlmark
    Moderator

    Re: Matsui MFi60 rusting

    You are missing something……
    they are crap!

    in reply to: Rogue Traders BBC Wed 10th #311149
    eastlmark
    Moderator

    Re: Rogue Traders BBC Wed 10th

    that means 15 minutes of acutal informative investigative journalism and 45m of cheap light entertainment for the brain dead then.

    in reply to: whirlpool branded smeg dishwasher pcb #310469
    eastlmark
    Moderator

    Re: whirlpool branded smeg dishwasher pcb

    Thanks John and yes that is the smeg part number……

    ….only its too late, I had to order it from Whirlpool and it arrived today!
    £119 to me rather than £70 from Smeg. dammit!

    thanks for the response anyway.

    696290824 for the record.

    in reply to: w/pool heater #311115
    eastlmark
    Moderator

    Re: w/pool heater

    481225928927 and if you can find a cheap source for them let me know, changed loads……and dont expect to get a complete pump as you might have expected when you look at the price.

    in reply to: is this too expensive? #311063
    eastlmark
    Moderator

    Re: is this too expensive?

    no, needs a door seal by the sound of it though.
    and cheap compared to the other one he is selling……here

    in reply to: Miele Dishwasher HG01 PREMIER #310990
    eastlmark
    Moderator

    Re: Miele Dishwasher HG01 PREMIER

    the standard drain hose with the 90 degree end from connect or who ever will fit these, its a tight squeeze but it does slide over. Not as thick and strong as the original but a whole lot cheaper.

    in reply to: module for vtd60g #308620
    eastlmark
    Moderator

    Re: module for vtd60g

    VENTED Drier for heavens sake! Timer, motor, heater, Belt!


    sorry!

    in reply to: Just lost the job #310719
    eastlmark
    Moderator

    Re: Just lost the job

    or a certain other company that supplies “gen” parts loose, no box or label?

    in reply to: Just lost the job #310716
    eastlmark
    Moderator

    Re: Just lost the job

    funkyboogy wrote:we normally advise customers that we wont warranty any part that they are able to get cheaper of the net…

    if they want our services with a peace of mind warranty on the job then they have pay…

    if not they can go else where…most are ok when you explain

    ally

    this is what its all about. If the customer sources and buys the part themseves then they are responsible for either chasing credits/refunds etc should that part fail again, whats more we are entitled to charge again for fitting the replacement should that happen.

    in reply to: module for vtd60g #308611
    eastlmark
    Moderator

    Re: module for vtd60g

    really looking forward to seeing one of these, how many eeprom/module combinations are there……..

    in reply to: Smeg D/W #310554
    eastlmark
    Moderator

    Re: Smeg D/W

    mains fliter, if your lucky its at the front 😆 ……….if your unlucky and its intergrated. 😥

    in reply to: Bosch SGV43A03GB/42 dishwasher – strange fault. #310534
    eastlmark
    Moderator

    Re: Bosch SGV43A03GB/42 dishwasher – strange fault.

    change the fill hose to a normal rubber type, doesnt transmit the noise like the rock hard Bosch type do. Could be the cheapest easiest way out of it if the fill tripping is not causing any other issues.

    in reply to: Bosch WFT2800GB/13 Dryer not heating #309856
    eastlmark
    Moderator

    Re: Bosch WFT2800GB/13 Dryer not heating

    seem to remember that could be the case. Had similar before, just slave on any old heater element to prove it.

    in reply to: whirlpool branded smeg dishwasher pcb #310466
    eastlmark
    Moderator

    Re: whirlpool branded smeg dishwasher pcb

    never did find the answer as I have just found at at considerable cost! Can get by on the full size but not the 45’s

    in reply to: Double inlet hose #310413
    eastlmark
    Moderator

    Re: Double inlet hose

    RocketMan wrote:Hi,

    Seen one of these fitted on a WD420. Does anyone know the part number???

    Could do with a few for spares

    Thanks

    Steve

    looks like a nasty kink in the making on that one though once its pushed back 😉

Viewing 15 posts - 1,651 through 1,665 (of 4,480 total)