Forum Replies Created
-
Posts
-
Re: Electrolux ESL DW series – access in the base
RocketMan wrote:I have to replace a heater on one of these. If I remember rightly they’ve got a molded plastic base. How do you access the heater? Is it similar to the Bosch SGS solid base? The whole top off?
Thanks
would need to full model number to be sure but, as far as I know, most elux dishwashers do have a removable access cover on the base, its just difficult to see it till you have it on its side. If not, the older ones have a metal panel stretching along the lower back between the side panels which can be removed for heater access.
Re: miele wt945s
no feed to the drain pump is a common Miele issue, new power pcb is the cure, never had it on a washer dryer though.
Re: Partfinder
ne, even with serial numbers we still end up having to measure stator sizes other oddballs. Indesit have to be one of the worse manufacturers for changing seemingly irrelevant items that then reflect the software needed.
Maybe the version the indesit engineers use is better, I don’t know.Re: 1607W not selecting.
what manual are you reading Steve? button S1 is the on/ off switch, hold down the door opening button and then swtich on for a total re set. no child lock on that one as the controls are locked anyway once a cycle is started. Sounds like it may not have finished its previous cycle.
correct manual is: http://www.ukwhitegoods.co.uk/downloads … manual.pdf
Re: Football Season 2014/2015
nice evening at the lane last night v Burnley, we gave them a head start yet they still managed to mess it up, against what Jim would call a B team as well.
Re: Siemans/Bosch DW Programing Guide Module 00269965
have always kept configuration sheets but they don’t show the part number, but looking at the picture of the module, this looks the likely one.
Re: What Really Happened
he does have some key contact within the BSH service network that is for sure and then makes out its all his knowledge.
As for his AKSO knowledge it is zilch. I recall Jim asking about a Neff/bosch old banger washing machine which was a re badged AEG which he confidently reported was an Asko. Anyone from that era (excepting Jim of course!) would have recognised it.
OT but his best moment was when he bragged that his credit card machine worked using satellites! He is always quick to answer and spread misinformation around and just as quick to ignore the responses when someone points out he is wrong as he has in the ISE thread reported here.Re: Siemans/Bosch DW Programing Guide Module 00269965
might have that on my van… too late/cold to look now though.
Re: Hotpoint D/Washer FDUD4812 new heater blown.
customer not bothering to clean filter maybe? either that or a duff circ pump at a guess.
Re: Smeg Range Model suk91mfx5 Error code FU14
there are no error codes on that model, its a simple dual fuel range with no electronics other than a relay pcb at the back. assume its just a faulty clock. could have a guess what the FU means though.
You have not mentioned if the oven is working or not? worth by passing the clock temporarily just to test it out if not. 816290735 is the part number but if before 2007 you may need a set of knobs as well.Re: induction hob half not working DeDietrich dti304je11
Don’t know that exact model but most have separate boards for each pair. Obviously check the terminal block fist though. If one of the boards is blown (IE track damage) then consider replacing the inductor as well.
Induction hobs….. not sure I have yet made any money repairing one! Big pile of incorrect or failed again pcbs cluttering up my workshop.
If anyone needs smeg inductor rings please let me know before ordering!Re: Ikea Renlig DWT160 Underfilling
under filling, regular issue not easily solved. Sometimes occurs after fitting configured PCB. Electrolux assured me it is the correct “new” efficient water level….. If you find an answer let me know.
Re: ISE w1607
timdowning wrote:Anyone got a door seal for a w1607?
The shop on here lists it but it says 14 to 21 days, so I take that to mean it’s not a stock item.
Thanks.
have to ask…. why? whats up with the old one? I could count on 2 fingers the amount of Asko door seals I have needed in 20 years.
