Forum Replies Created
-
Posts
-
Re: HJA5100 Wiring Diagram
if you want more help will see what I can do
if you want it done professionally look up get an engineer on this site . I will happily forward the diagrams to any trade site member
Dave
Re: Beko DSC85W
what makes you think its too hot
if the unit overheats there is a safety stat on the element that trip and has to reset manually
daveRe: Zanussi washer dryer
does the beeping noise start as soon as you switch on or as you try to start a programme ?
Dave
Re: HJA5100 Wiring Diagram
interesting pic
1 the connector block should not be there so someone has been playing
2 brown wire (yellow arrow) there should be a brown wire coming from the mains terminal block, through the cut out then on to connect to this wire. it provides power for the clock and main oven
3 white wire (Red Arrow) when clock is set this wires takes the live feed to the oven switch to power main oven
my guess is when you find this wire you will find another connector on it and it will join prob the brown one
the red and white one to the clock should be supplying the neutral
don’t know what the red and white are in the left hand terminal
just seen a black connector lower in the picture
bit of a mess, did you get someone out to do this to you ?
Dave
Re: Baumatic P3EHFI XO-B-U
sorry Franz to be honest did not look the model up ( don’t has tech access) . I was unaware they did commercial stuff and since most of the Baumatic units I see are domestic I assumed it would be a £40 fryer ( still learning )
also as with most takeover I would expect some cost cutting. so they will prob try to discontinue uneconomic part as soon as they can or ramp the price. Just got a quote for simple door lock on a domestic washing machine of £30 trade. customer was a bit shocked when I quoted for it
Dave
Re: BEKO washer, no heat?
are you getting any error codes
have you got access to tech info? if no will pm you some
Dave
Re: HJA5100 Wiring Diagram
if the clock timer was out of operation then the main oven would not work at all
if the fan is noisy then you will most likely need a new motor unit
if the small oven gets hot 1st make sure both elements are working. turn on with the door open and make sure the top element gets hot, also make sure the floor gets hot as without the lower element all you have is a grill. If it still gets too hot change the thermostat
cant give any wiring info unless you are a trade member but thermal cut outs
1 goes from mains terminal block live to the clock
2 goes from mains terminal block live to the convection oven switchfrom what your saying it sounds like a cowboy has been at it.
Dave
Re: Electrolux ESL6211LO – Error
instruction normally are with it if not can message them to you
as far as supplier ask the site shop as that helps to keep this site active
https://shop.ukwhitegoods.co.uk/
Dave
Re: Electrolux ESL6211LO – Error
the water level pressure sensor has been modified on this unit due to this type of problem so you need to order the kit and fit it
Dave
Re: Baumatic P3EHFI XO-B-U
candy has taken over Baumatic but unless it a consumer part like a filter I doubt they supply spares
does not hurt to askDave
Re: Zanussi ZDT 311 beeps 6 times
10 Degrees 9655 ohms
25 Degrees 4850 ohms
60 Degrees 1205 ohms
90 Degrees 445 ohmslist of resistance measurements for the ntc when disconnected
if it boiling a would expect it to read higher than spec
Dave
Re: Zanussi ZDT 311 beeps 6 times
well that might be it
How can you hear it heating ?
when a dishwasher is on the motor should be running so that drowns out the noise of the heater. if you have no motor then the heater will overheat. but i would have expected another error code
Dave
