Forum Replies Created
-
Posts
-
Re: Beko CDA539FW-2 fridge freezer
cant see one listed and its not shown on the wiring diag
have pm’ed you info i found
Dave
Re: Beko WMA 520 stopped working on final spin
part number as you have is 2817080100
email site shop and google for prices. cheapest i could see is Amazon but site shop may be able to match or improve on it
no alternative you have to fit the correct motor or the speeds may differ and alter the workings of the machine
Dave
Re: AEG Micromat KB9810E-M Displaying Safe
Deactivate child-proof lock
– If necessary, switch off the appliance by the START key.
– Press and hold “program” and “-” keys simultaneously until “SAFE” in the display goes out (approx. 2
seconds). Now the child-proof lock is deactivated and the oven is ready for operation again
try thisDave
Re: speedqueen les37awg3018 com dryer
i would go to google and Ebay as i find sometimes its as cheap to get things sent from the states as long as the price is cheap enough to avoid vat and import duty charges
ring JLA but do a bit of research as they can be a bit dear sometimes
Dave
Re: jackson oven elements
getting them off the shelf might be a problem but you can ask to see if one can be made
we have a local place in liverpool that can make elements
http://www.tpfay.co.uk/
you could ask them to see if they can helps or see if there is another firm that does the same thing near youDave
Re: Beko WMA 520 stopped working on final spin
am going away for the weekend but what i am thinking is :
there is a magnet at the rear of the motor that generates a voltage to tell the board what speed the motor is doing. if this magnet breaks the motor starts and gain speed very quickly( should be a slow rise). the board then realises that its not getting a signal and shut motor down and wont restart for safety reasons
if magnet has broken it a new motor part not available on its own
Dave
Re: speedqueen les37awg3018 com dryer
this is a bit of guess work and a bit of experience
they use a similar stat on maytag dryers
the two outside connection will prob be the ones you want to look at. i would say these are the main load to the heater
the centre 2 brass connector will either be
1 a resistor to preheat the stat or ( my best guess)
2 an NTC if the unit uses electronic controlthis system is used on maytag dryers
the last terminal is probably a changeover contact from the main set
meter through from left to right see if you get a connection
Dave
Re: Beko WMA 520 stopped working on final spin
when the motor starts does it seem to go very fast and then slow down and stop ?
Dave
Re: Beko Washing Machine
mentions E13 thought you would have made a mistake as the errors seem to be all E**
Dave
its also one of those machines on the changeover to brushless motors, the manuals listed for it are brush motors but the motor is listed as brushless
Re: Oven & grill not working – Zanussi ZBS 773
just looked up your model and it seems the electronics control everything
from that I would expect it may be a board fault and difficult to fix yourself without expert help
Dave
Re: fridge/freezer costing £50pm in electricity. Is this fau
electricity is measured in kilowatt hours or 100watts for 1 hour
or 100watts for 5 hours
with that in mind if your fridge draws 70 watts that 1000 / 70 = 14.29
which mean it will use 1 unit of power in 14.29 hours
based on 17p per unit and a month of 30 days
hours in a month 30 * 24 =720no of units per month 720 / 14.29 = 50.38
price 17p * 50.38 = £8.56and thats based on the motor running all the time which if its working ok it should not
Dave
Re: Beko condenser dryer heating problem
you cant short the ntc out as it still wont work. value has to be within a range. too high or too low it wont heat for safety reasons
your post reads 2 ways. at the top it says you shorted NTC but at the bottom you seem to say you swapped it Which ??
get an old one off a Hotpoint heater and plug that on. I carry one in my bag for that purpose
Dave
