[electrofix]

Re: Fisher Pakayl Dish Drawer

I had similar problems with those buttons and It was a positioning problem from memory
cant quite remember how it fits but check the buttons, and the sensors for them underneath, and how they connect to the pcb

Dave

[electrofix]

Re: Belling Gas Oven Timer Faulty

yes timer can be faulty as it controls the oven if you want it to cook when you are out

you need not replace the timer if you don’t want to but you would need to bridge it electrically so the oven would work
since we would not condone amateurs working on gas appliances I would suggest you look on this site for a suitable professional who will not only fix the problem but ensure the appliance is safe

Dave

[electrofix]

Re: Fisher Pakayl Dish Drawer

has it got a child lock ??

Dave

[electrofix]

Re: E36 on Zanussi ZWD 1471s

you cannot blow into the black pressure switch or you can destroy them
and no it does not click and now it may not work

Dave

[electrofix]

Re: Flavel oven seal

I have pm’ed you a picture of the model above

prod code 7719986337

DD AP10FRKP-1 FLAVEL 100DF FSD BLACK

from diag
item 488 part no 455920052

the one on the left is not listed so I assume the above is what you need

Dave

[electrofix]

Re: Neff fridge/freezer (K8614X3GB) behaving erratically

but it will list thermostats (thermistors) and may give you a general idea of position

Dave

[electrofix]

Re: Neff fridge/freezer (K8614X3GB) behaving erratically

if you go here http://www.neff.co.uk/store/

put your complete Enr in you get a complete parts list and diagrams

Dave

[electrofix]

Re: Beko dcu 9330 R condenser dryer

have you checked the condenser is locked in

there is a red tab that has a switch on it and if its not locked it wont start

Dave

[electrofix]

Re: 15amp 20mm ceramacic fuse for a panasonic M/wave

there is a service manual on mediator on connect list all the part numbers including a fuse
15 a 5045171105449

Dave

[electrofix]

Re: Panasonic Tumble Dryer NH-P80G2

I assume exactly like the air-con in your car when you use it demist the screen. hit the clothes with dry air and the water will evaporate. by not heating the clothes or by only heating a bit it will be more energy efficient

Dave

[electrofix]

Re: Hotpoint 9605 top loader.

@ iadom

was it the 1502 where the knob glowed red when it was on

can see what you mean about the timers changed a few but it was the mechanics that went down the tubes in the 1504

its a shame the whole world has changed. it used to be buy our product its “Quality” now its buy our product its “Cheap”

Dave

[electrofix]

Re: hoover vision dryer drum constant spin

if the relay is closing without the start button being pressed its got to be the board

Dave

[electrofix]

Re: Hotpoint 9605 top loader.

they got to the best design on model 1504 before date code 02

on earlier models.
motor was 4 pole not 2 so motor was running at half the speed.
pump had 4 blades (not 2 ) and water seal and bearing seldom failed in fact it lasted so long the pump valve failed first causing it to bounce causing water to come out in spurts.
there was also a needle roller bearing on a strut on the bottom of the gearbox. to support the pull of the belt. later machines get oil leaks as the lower box bearing wear because its not there
the clutch shoes are like car brake shoes, an ali frame with a friction material bonded to it

Dave

[electrofix]

Re: hoover vision dryer drum constant spin

have you checked the start switch ?

Dave

[electrofix]

Re: Miele logic board problem (I think).

does it heat on any programme ?

Dave

[Author]

Posts