Forum Replies Created
-
Posts
-
Re: ZANUSSI ZBB28651SA INTEGRATED FRIDGE FREEZER-FAULTS
how old is it now ?
is it still under guarentee ?
Dave
Re: Hotpoint FFAA52 Not Working
it is obvious something has pulled a lot of current. fitting a new board would only result in the same thing happening. you have to find the reason.
on the second pic something is connected to the connection where the track is damaged. you need to find out what that is first
you may be able to resurect the board by replacing the damaged tracks by wires and soldering them to the componetsDave
Re: Bosch Classixx Dishwasher – SMS40C12GB/13 Type SI6P1B
if you want a parts exploded veiw go here
http://www.bosch-home.co.uk/store/spareparts/search
Dave
Re: drain pump for bosch wash/mch mod number WAE24166GB/06
bosch part no 00144978
go to site shop
http://shop.ukwhitegoods.co.uk/catalogs … /?q=144978
you will see some alternatives
Dave
Re: Hotpoint FFAA52 Not Working
dont repair many fridges but where the lights and temp knob is normally the board
board part number should be C00265143 but double check before you order in case there is more than 1 board for this model
you could also try
http://www.qer.biz/servReps.htmwho can repair some boards
Dave
Re: Bosch Classixx Dishwasher – SMS40C12GB/13 Type SI6P1B
it is unlikely the pump is causing your problem. the drain pump is a 2 wire device and has no attached earth.
you state that the tablet has just been released and since the machine has not heated at this point i assume you have it plumbed to hot water otherwise it would be cold
it there any water visible in the base ?Dave
Re: Hotpoint FFAA52 Not Working
there are a few things it could be
first put you hand on the compressor and see if its warm
if yes there is power going to it therfore fault could be
1 compressor failure
2 some compressors are capacitor start some are relay and these failif no
circuit board or poss ntc (thermistor which is the temp sensor). but i think if there is a fast freeze button it overrides thermistor but uncertain of thatmy bet would be on the board
Dave
Re: Miele DA2210 extractor hood
some miele appliances have wiring info hidden inside have you had a good look around
Dave
Re: White Knight Condenser Dryer
sound like a rear seal has failed alowing moist air to get out
Dave
Re: Hotpoint 17450 motor cutting out
wow that brings back memories
thats a start relay. the motor has 2 windings. a start winding and a run winding. when you switch on the power to the run winding goes through the relay coil and since the motor is stationary at that point the coil on the relay produces enough magnetism to lift the core inside the relay and closes the top 2 contacts (yell and grey). this energises the start winding and the motor starts. As the motor speeds up the motor current drops and the relay drops out
the start winding is a high current winding but will burn out if left on too long. Also the relay must be in the correct position as it is gravity concious so operating these units on their side or upside down will destroy the motor
the motors have an overload in the windings and it sounds like yours may have failedDave
Re: Hoover Vision HD condenser dryer showing tank full
very likely
my reason for saying the above is if the stats go open circuit it can bring the light on. it does on hotpoints and i think hovvers do too but not sure
Dave
Re: Hoover Vision HD condenser dryer showing tank full
first check on this would be the thermostats on the heater ( if unit is heating these will likely be ok )
if they are ok most condensor dryers have a float in the bottom that senses water level this could be stuck
Dave
Re: Sevis SUPERTWIN 110 – 111 Bearing Hub Required (For spin
qualtex still showing unt08 in stock
Dave
