[electrofix]

Re: Bosch SRS55L22GB/01 D/W – Module problem

as with all electronics it can be blown with no visible signs

you need to find the mains voltage to the board

a lot of boards have a fusible resistor and these can go for no reason sometimes. normally its about 100 ohm

Dave

[electrofix]

Re: Beko wmb91442lw 9kg w/m

last message i got was when you said you were more confused

Dave

[electrofix]

Re: Kyoto spares

put that into Qualtex and a load of Brandt spares came up (27 of them )

Dave

[electrofix]

Re: samsung w/m J1453S

there are some spares that are cheaper new on ebay than from trade suppliers

Dave

[electrofix]

Re: Kyoto spares

typed kyoto into Qualtex and some Beko spares popped up which may mean it could be Beko in disguise

do you have model no’s

Dave

[electrofix]

Re: samsung w/m J1453S

this is a long shot

http://www.ebay.co.uk/itm/Samsung-j1453 … _278wt_958

seller has the board but you would have to message him to find what his fault was so you can figure out if the board is faulty or not

says collection only but i dont know where you are based and you may be able to convince him to send just the board by myhermes

Dave

[electrofix]

Re: samsung w/m J1453S

i would message this site shop first and then connect. both list a few part for this machine

not going to be cheap are you certain board has gone and more important, if it has why ?

Dave

[electrofix]

Re: awoe9558 drain pump

have you seen this ?

http://www.ebay.co.uk/itm/maytag-mwa-09 … 1289wt_805

according to qualtex this is right part no but you will have to double check

Dave

[electrofix]

Re: Rangemaster RDW6012FI Dishwasher Lower Spray Arm No Wate

you are prob on right track. you will find the dishwasher has a half load facility.
if customer does not use it strip valve and remove the plastic flap

Dave

[electrofix]

Re: ZWF1020W Washing machine-error code

its fault 3 series

which are all pressure switch faults

there are 2 pressure switches if they dont agree fault 33 pops up

there are 5

fault 33 pressure switches dont agree reasons include faulty switch, heater earth fault , oc heater , faulty wiring or pcb

fault 35 flooding pressure switch or wiring fault

fault 36 , 37 and 39 are all pcb fail;ure faults

have got tech info if you want some light reading but need prod number as there are 3 listed ending 00 , 03 and 04. may be same info but best to be sure

Dave

[electrofix]

Re: Electrolux freezer startup problem

if i am right its a component on the board that has failed not difficult to an enginner who is up to date but unless you know electronics you would have to replace the whole board

you could look on ebay QER advertise on there they may repair and test this board

cost as far as i can see around £60 new

Dave

[electrofix]

Re: Electrolux freezer startup problem

sound like a pcb problem

not an unusual problem these days

easily fixable with the right engineer but if you call electrolux they would put a whole new board in

dave

[electrofix]

Re: Bosch engineer might know

if its under 2 years old its under guarentee

there is a resistor that blows sometimes on the pcb where the power goes into the power supply. from memory think its 100 ohm fusible

Dave

[electrofix]

Re: Diplomat ADP8242 dishwasher

still might be beeping

it washes, heats then you hear 2 very quiet beeps and keeps washing

anyway looks like a smeg in disguise

if so look at timer board and if its at the top of the door change the power supply capacitor its either 1 or 1.5uF

cant promise it that but its very likely. cap supplies voltage to board if it gets too low board crashes

Dave

[electrofix]

Re: Diplomat ADP8242 dishwasher

assume you mean a dishwasher

does it start and then go bleep bleep ( very quietly) and seem to start again ?

Dave

[Author]

Posts