Forum Replies Created
-
Posts
-
Re: Zanussi FL 1034 not heating
have you checked pcd for bad solder joints
have some info if you let me have an email address seems to cover a range of machines
Dave
Re: Bosch SGS45C02GB/02
according to bosch site vdoes not look like it has impellor jug only item 0429 safety system part no 490618
first look for the obvious valve coils, kinked hoses, and the old favourite tap turned off
Dave
Re: old hoover
codes
-6 rinse 1
-5 rinse 2
-4 rinse 3
-3 rinse 4
-2 spin
-1 condiioning rinse
0 endhave you tried pressure bell ?
Dave
Re: Possible PCB Repair?
if it is the heater relay no problem
follow heater wires one of them will go back to the board and the connection will lead you to a small black square unit soldered to the pcb ( some can be white )
first check you have not got bad solder joints on the relayDave
Re: This guy is mental!
to get hits on youtube is the only answer
dipstick (polite version) is the other lol
Dave
Re: Electrolux Built in Oven (949712544)
my first guess would be the clock check if its in the manual postion
Dave
Re: wirlpool american style top loader washer
what type of fuses are you putting in ?
the correct fuse should read T6.3A not F6.3A
I use the microwave fusesT= time lag F= fast blow
the fuse on these machine is pretty sensitive to overloading so it may seem it has blown for nothing check to see if customer put too much in
as a guide
take an old fuse and carefully open it by cracking the porcelain look at the wire inside
if it has blown through an overload most of the wire will be there just a bit melted in the middle. if it has blown through a short circuit there will be no trace of the wirehope this helps
Dave
Re: AWP510L board blown twice !!
you need to look where the board has blown and what part was it controlling
could be a chaffed wire that only shorts out on heavy loads so you need to trace wiring and work out current flowpost a good Pic of the blow board one of us may recognise where the tracks go
Dave
Re: AEG Lavamat 86741 model -waste pump problem?
no probs m8 glad you got it sorted
it it goes again you can normally you can buy just the motor part seperatly saves you buying a new gen pump unit
Dave
Re: LAMONA HJA8704 Door locked
if its a standard interlock should open if you pull the plug and wait 4 mins
its supplied by howden joinery hence model HJ etcfrom all info on this forum ( search for HJA8704 and search for lamona) they are a pile of tat. seems to me the enginner nust have done some sort of reset of some kind before so its trial and error unless another member knows better. if the interlock is not a bi-metal there may well be an emergency release mech
Dave
Re: AEG Lavamat 86741 model -waste pump problem?
if there is no way to get in from the bottom then
the front of the machine comes off
you have to remove the control panel, door gasket and door lock from the front and undo screws and it comes offDave
Re: Ariston FV271 cooker is kaput
could be the clock if the clock relay has blown nothing will work
Dave
Re: AEG Lavamat 86741 model -waste pump problem?
chances are the pump has gone but you access it from underneath. pump is on the left of the filter housing and you have to riase the filter housing up (about 1/2 inch) to withdraw the pump and check. it is a common pump so not expensive
Dave
Dave
Re: Synchronous motor timer for a water softener needed
these liitle units where used quite a lot on older machine only modern day part is on central heating valves
try
http://www.bes.co.uk/products/112.asp?k … base#11025
or
http://www.toolstation.com/shop/p38289
also a lot of local plumbers merchants will stock these
looks very similar to me the only if i can think of is it may turn clockwise or anti-clockwise but its cheap enough
Dave
