Forum Replies Created
-
Posts
-
Re: Fridge freezer problem in Malta
if its a 12v fan there must be a printed circuit board controlling it.
fimd the board and look for damageDave
Re: hotpoint WD 63S tripping rcd after cycle
I agree it a bit weird does it trip as the door unlocks or a minute or so after ?
does it happen every time ? (intermittent faults are a pain)
try disconnecting tumble dryer heaters and running programme see if it does it then. if customer does not use dryers elements can get damp over time
if the machine is left switched on will it trip over and over again or just the once?
As for motor if you think it may be carbon dust there is no reason you cant disconnect earth to motor for a test while you are there. no earth means it cant trip rcd as it is mounted on plastic tub
Dave
Re: Risk Assessments
never done them and would not know how lucky only have 1 employee.
its a sad state of affairs when people cannot take responsibility for their own actions and even worse when lawyers win cases on this sort of rubbish.
life is full of risk but you have to be sensible. These sort of cases should only suceed if the employee was forced to do a task that was unreasonable to expect them to do. you can pull your back tying you shoe laces and getting out of bed. how far will this over protective health and safety situation go?
i live test machines all the time. i hold live pcb’s in my hands and check components. health and safety would have a field day if i asked anyone else to do itDave
Re: Eurolec / Waterline.
only place i found any parts was europarts maddocks
europart.co.uk
they list a boot , pump, interlock, and door handle
looks like it might be a Fagor machinemay be worth a ring
Dave
Re: hotpoint WD 63S tripping rcd after cycle
if it tripping the rcd you are looking for an earth fault. door lock does not have an earth so unless its wet cant be that
megger all elements and motorDave
Re: Hotpoint WM11P running on
you have to also check the number of clicks some have 1 2 or 3 stages
this one looks like a 2 stage ( should have term numbers 11,12,13 + 21,22,23 ) therfore it should click twice. the problem, if there is one, will be on the lower set (11,12,13). As the water drains out if the lower one does not drop out some machines can run on.
try just a spin see if it runs on then. if no then prog is prob ok. then try last rinse and spin see if it does it then. if it does try it again but this time during spin give the switch a tap. its a case of trial and error but you have to get the correct switch for your machine otherwise you have to adjust all the perameters of the switch and that can take timeDave
I think EMW test and recon these timers you could ask them
Re: SEBO X1 FAULT CODES
found the owners manual if it helps
http://sebo.co.uk/support/downloads/man … Manual.pdf
take it you have checcked brushes, motor for continuity etc
Dave
Re: Belling format 500CR energy regulator
have you got the number off the regulator as it is probably a standard one
Dave
Re: Diamond H 42ER101C1dual circuit energy regulator problem
have you looked here
Dave
Re: Hotpoint WM11P running on
check for blockages in pressure circuit or pressure switch
a lot of old machines if pressure switch stuck just starts prog again
Dave
Re: AEG LAVAMAT 6955
try
Start of Customer Service Test Programme:
With pre-wash and short wash buttons depressed, set rotary selector knob to ?gentle spin?.this starts test prog and should reset faults
Dave
Re: TDS Disc
got full tds disk on my netbook
using virtual cd and an iso image of disk running no probs
using same system no 2 shop computers therfore 1 disk on 3 comps
Dave
Re: Neff Dishwsher Spray Arms not rotating
if its not a blockage its a motor problem
take both bars off. check for blocked jets and clean them out
fill and start machine without bars in and when motor starts let it run for 5 secs to push any rubbish through
replace bars and see what happensif this fails you need professional help
Dave
