[electrofix]

https://www.ukwhitegoods.co.uk/forums/member/63086-appliance-repair-aberdeen

posting again links to website for repairs in aberdeen

do we delete or leave this. are they trade members ?

Dave

[electrofix]

as far as i know you either use lock ring or braze the tubes

like this

https://www.youtube.com/watch?v=EwQSH_NdaLU

Dave

[electrofix]

video will be too big
upload to utube or another site and then post a public link

Dave

[electrofix]

cant be drawring high current or the fuse would go

as with all power issues check socket and check the plug. had one 2 hours ago where the fuse in the plug had been burning stopping the machine

also with later machines the power cord is plugged in at the rear. make sure its all the way in and check if its burnt by pulling the plug out and checking it

Dave

[electrofix]

if you look at the links the part numbers are in the text
so from the link
shop.ukwhitegoods.co.uk/ele4123-cooker-energy-regulator

part no is ELE4123
so google search that

other links work the same way

Dave

[electrofix]

you will probably have to turn it on its side, take the base off and loosen the sump clamp to be able to drop sump to get it out of the way enough to release motor that will be jammed against the rear wall

its not too bad a job once you get into it

this is an american manual but will be similar

https://www.manualslib.com/manual/3111760/Miele-G2000.html?page=87#manual

Dave

[electrofix]

to find out if spares are available would need serial no

have they called the cooker leisure as it may not be a brand name not a manufacturer name

leisure is now part of Beko who also own Flavel. Beko now own most of hotpoint but designs are different for the moment

stoves as you say own belling

Bosch stuff is ok as is Neff which is same company

as for what good at the moment will tag in Don he is more on the retail side of things

and take into Account K’s comments above because you often forget inflation when looking for new appliances which leads to lower quality over time

Dave

[USER=”125″]don[/USER] comments

[electrofix]

thats a safety stat so will have a low ohms reading

if it was the element expect 30 ohms or so

Dave

[electrofix]

check pressure chamber if clear then check heater resistance

Dave

[electrofix]

board is at the back on most of these models

check heater element

what error codes did you get ?

possibly a water fill or drain code

if yes bet the pressure chamber is blocked

can be accessed inside wash area sump

half moon bump in sump.. I normally put about 2 cups of warm water in then bend cable tie into chamber and move it around to dislodge debris

if unit thinks there is not enough water in or there is not enough water in it will not engage heater

Dave

[electrofix]

real fun
twin motors turning one belt
motor modules used to fail as well

really solid machine but they just ovelooked corrosion under water

only machine i knew with a quilt programme

Dave

[electrofix]

double check the door as have had instances of door switch opening when it gets hot. door warping or the like

it has got a float. all condensor dryer have to to indicate container full

when it goes off can you restart at once or do you have to wait ?

Dave

[electrofix]

most dryers have a timed programme
have you tried running that ?

Dave

[electrofix]

no chance, unless you have a freindly bosch service agent you have no hope

another option that may be cheaper is

https://www.easypcb.co.uk/

not used them myself but other forum members have so cant attest to reliability but your fault does sound like a power chip which are really cheap and easy to fix

Dave

[electrofix]

if temp sensor had failed you should still have lights

assume you have tried a different socket just in case but it does sound like a power chip failure on the circuit board

lookied up the module up and its £66 so £90 sounds a bit steep

cant promise I am correct but module sounds likely

Dave

[Author]

Posts