fasetester

Forum Replies Created

Viewing 15 posts - 136 through 150 (of 540 total)
1 2 3 … 9 10 11 … 34 35 36
  • Author
    Posts
  • February 27, 2013 at 3:33 pm in reply to: indesit washingmachine wib101 #391130
    fasetester
    Participant

    Re: indesit washingmachine wib101

    thanks martin for your reply. do i tighten the bolt as tight as it will go. i was afraid of snapping the bolt. when the pulley is turned round should it run even.fasetester

    February 11, 2013 at 4:18 pm in reply to: bendix tm310w no heat #389875
    fasetester
    Participant

    Re: bendix tm310w no heat

    thanks martin while from i worked on condenser dryer how do i test the dryer to make sure it is working properly 😳 fasetester

    February 11, 2013 at 4:03 pm in reply to: bendix tm310w no heat #389873
    fasetester
    Participant

    Re: bendix tm310w no heat

    dont know martin. just want as much information before check dryer. said dryer is not used much.stopped heating thanks fasetester

    February 8, 2013 at 3:39 pm in reply to: intergrated dishwasher BFI62 #388924
    fasetester
    Participant

    Re: intergrated dishwasher BFI62

    thanks jem for your help fasetester

    February 6, 2013 at 3:59 pm in reply to: intergrated dishwasher BFI62 #388922
    fasetester
    Participant

    Re: intergrated dishwasher BFI62

    thanks jem for the reply. that is the white and blue cap in the picture. not the 2 black does. the new ones have to be the same. and where is the best place to get them thanks.fasetester

    February 5, 2013 at 5:47 pm in reply to: intergrated dishwasher BFI62 #388920
    fasetester
    Participant

    Re: intergrated dishwasher BF162

    thanks jem for your reply. removed pcb cant see any thing burnted. or cap bulging only thing i could see was heat sensing wire plug slighty loose. resoildered it still the same. what are x2 the cap on the pcb should the show damage how do i test them


    what sort of reading should i get thanks fasetester.

    February 1, 2013 at 11:29 am in reply to: intergrated dishwasher BFI62 #388918
    fasetester
    Participant

    Re: intergrated dishwasher BF162

    checked heater and wiring checked pump float sw is this a no heat fault any info fasetester.

    January 18, 2013 at 3:24 pm in reply to: creda dishwasher #388139
    fasetester
    Participant

    Re: creda dishwasher

    thanks martin for reply was to get back with mod number 🙂 fasetester

    November 7, 2011 at 4:01 pm in reply to: indesit washing machine pulley working loose #363015
    fasetester
    Participant

    Re: indesit washing machine pulley working loose

    chippo wrote:You might need to replace the pulley if there is movement on the shaft.

    thanks chippo for your reply fasetester

    November 7, 2011 at 3:59 pm in reply to: indesit washing machine pulley working loose #363014
    fasetester
    Participant

    Re: indesit washing machine pulley working loose

    cab wrote:yep, is it made in china by anychance? like the one I did today, it was one of those currys essencial thingys

    it has come loose before when machine was not long new so when the bolt is tightened if their is still play need new pulley. thanks cab

    November 4, 2011 at 5:18 pm in reply to: indesit washing machine pulley working loose #363011
    fasetester
    Participant

    Re: indesit washing machine pulley working loose

    cab wrote:LOCTITE

    thanks for your reply cab the tread sealer type you use for general bolts that you get in car care

    July 1, 2011 at 2:36 pm in reply to: zanussi washer mod zwf14070w1 #354430
    fasetester
    Participant

    Re: zanussi washer mod zwf14070w1

    thanks BOB cris dave for your help. went to machine today done a reset put it on a wash rince and spin and back to working order.

    think it was over foaming had put it throught a rince fair few times to get read of the suds thanks again fellows.fasetester.

    June 30, 2011 at 6:53 pm in reply to: zanussi washer mod zwf14070w1 #354427
    fasetester
    Participant

    Re: zanussi washer mod zwf14070w1

    yes electrofix sent me the manual just need to figure out the flashing red and green if you disconnect the appliance parts heate ect and it was faulty would the appliance start a normal programm. you should get no reading between heater and earth. or what is the min insulation reading thanks fasetester.

    June 30, 2011 at 6:22 pm in reply to: zanussi washer mod zwf14070w1 #354424
    fasetester
    Participant

    Re: zanussi washer mod zwf14070w1

    any reply welcome if possible within next 30min going back tomorrow morning thanks fasetester.

    June 30, 2011 at 4:14 pm in reply to: zanussi washer mod zwf14070w1 #354423
    fasetester
    Participant

    Re: zanussi washer mod zwf14070w1

    when testing this machine if i disconnect the heater. or any other part would it start to operate. if the part in question was faulty by reading other post a lot of pointers go for pressure switch. or heater

    then some replace pump pressure switch heaters ect and still cant get the appliance to work.

    you can dig your self into a hole a cust wont pay for appliance that is not working.fasetester

  • Author
    Posts
Viewing 15 posts - 136 through 150 (of 540 total)
1 2 3 … 9 10 11 … 34 35 36