funkyboogy

Forum Replies Created

Viewing 15 posts - 1,606 through 1,620 (of 2,407 total)
  • Author
    Posts
  • in reply to: Beko condenser dryer DRCS68W #296763
    funkyboogy
    Participant

    Re: Beko condenser dryer DRCS68W

    they also have a drying sensor inside front lip @ door area ,
    may be fluffed up , or faulty

    ally

    in reply to: samsung RS20 #296383
    funkyboogy
    Participant

    Re: samsung RS20

    you would be lookign at the wrong end of £200.00
    maybee someone on ukw could assist if they are local to u…
    we are in cent scotland..

    you would be best to determen if you are getting 240 to compressor b4 thinking about replacing comp etc..

    ally

    in reply to: Watch out for the dodgy doorstep salesman. #296509
    funkyboogy
    Participant

    Re: Watch out for the dodgy doorstep salesman.

    do they still pay a BIG one six for a complete, if so you should have jumped at it.. i mean 16 a complete you could retire round about 3040..

    where do these people get off … dont answer that ?

    they must have a eprom slot in the back of the head where merloni brainwash them to believing 16 is a fair fee ..

    ally

    in reply to: samsung RS20 #296381
    funkyboogy
    Participant

    Re: samsung RS20

    if compressor is making a slight ping noise then cuts off /on > then comp faulty.. and would be a system job if cust wants repaired ..

    other wise it may be a pcb fault , but on the surface of things it sounds like compressor failure

    ally

    in reply to: Snobby Geits!!! #295480
    funkyboogy
    Participant

    Re: Snobby Geits!!!

    r.e orig post … i take my hat off to you if you are removing canopy island hoods to repair them yourself..

    when i get some arsy ponced up whatsit wi stuff like this i advise them to have it removed by installer to avoid damage etc to their showpeice kitchen.. this normally does the trick.
    ally

    in reply to: BEKO WMA745W #295235
    funkyboogy
    Participant

    Re: BEKO WMA745W

    cheers , i know the second part is defo an L , got me wondering now about the 1st letter , as it wasnt as defined as the L.
    i did mess about with it a little , when you hold start button and switch on …all the leds lit up and a small l appeared in top left display ,

    i set prog to spin and it just filled up with water , wouldnt do anything else

    ??????…ally

    in reply to: BEKO WMA745W #295230
    funkyboogy
    Participant

    Re: BEKO WMA745W

    you could have apoint there ?
    is this a fault code are r u guessing

    ally

    in reply to: sinclair c5 #295119
    funkyboogy
    Participant

    Re: sinclair c5

    MAYBE A MOTOR OF A TREADMILL ,
    they look pretty solid, and are designed run under load etc …

    ally

    in reply to: Oldest customer ? #294936
    funkyboogy
    Participant

    Re: Oldest customer ?

    young people
    always tell you their excact age.. ie im 4 years and 7 months …

    middle age
    are always a bit vague ,,,,

    but why do old people always tell your their age, even when youve not asked ????? , i doesnt matter what your doing it always creeps into the conversation.. im mean what do they want you to say back to them…

    any tips … appart from oh well youve not got long to go then..
    or well yes i can see why you want to repair , no point in buying a new one ..

    lol ..ally

    in reply to: Haier No spin #294068
    funkyboogy
    Participant

    Re: Haier No spin

    or a tech leaflet from haier ??

    ally

    in reply to: Samsung P1453 #294491
    funkyboogy
    Participant

    Re: Samsung P1453

    YIP PCB REQUIRED FOR THIS …
    ALLY..

    in reply to: ELECTROLUX OVEN PYRO TYPE MOD EPSOPMSS PD 944250330 #294310
    funkyboogy
    Participant

    Re: ELECTROLUX OVEN PYRO TYPE MOD EPSOPMSS PD 944250330

    tried that , put lock on and then off again ..
    cheers for reply..

    any other ideas ??

    ally

    in reply to: white knight c/d WK767C #294205
    funkyboogy
    Participant

    Re: white knight c/d WK767C

    CHANGE HEATER AND STATS..
    also check rear fan bolt is tight, dont tend to get to much bother from these, … if wanting to kepp repairs to minimum try changing stats 1st

    ally

    in reply to: Check out your digits #294104
    funkyboogy
    Participant

    Re: Check out your digits

    never mind if you missed , only another 1000 years before it comes aound again..

    in reply to: Kenwood KDW243A #294095
    funkyboogy
    Participant

    Re: Kenwood KDW243A

    LITTLE BRASS TOC @ REAR WILL BE O/C 2 MINUTE JOB
    ALLY

Viewing 15 posts - 1,606 through 1,620 (of 2,407 total)