[geoff1]

Re: wf 240 intermittent wont light up

Sounds like the switch its self or solder joint broken on one of the legs

[geoff1]

Re: Hotpoint WDL540 drains for approx 5 seconds then stops

Is the water inlet valve ok?

Geoff

[geoff1]

Re: wf 240 intermittent wont light up

I have had a number of these boards with either the on/off not always operatng of the start/cancel intermitant working.

Althought the tact switch may feel ok the solder joints on the pins where it joins the module fail.

I carry a board so I can couple it up to the cable to prove if it is the switch and if it is carefully try to re solder pins or replace switch from scrap board

HTH

Geoff

[geoff1]

Re: Neff H7871N2GB/02 Circulation fan

Hi

Main oven fan motor assy 092676 (fits many microwaves and ovens check espares)

Just in case the stirrer/magnetron fan motor is 087672

Geoff

[geoff1]

Re: Whirlpool AWO/D4605

Education was the answer.

1 small quilt and 1 sheet

Customer in a panic as this load was not spinning 😯

OOB 😆

Geoff

[geoff1]

Re: Zanussi D/W hinges

Hi Jim

No details on Pro corner but connect and other suppliers show it as a pair and call it a kit

HTH

Geoff

[geoff1]

Re: DHL DELIVERY

Just spoke to Connect about order placed Friday which has not been sent yet.

Advised that they are holding orders at connect while DHL clear the back log to the north.
Have been told that I will get update to morrow. 😡

Geoff

[geoff1]

Re: Whirlpool AWO/D4605

Hi

Will recheck motor wiring as last time I was there I could find no problems with it. Pressure chamber nice and clean

As to the fault it will spin one day then the next it will not.

Geoff

[geoff1]

Re: DHL DELIVERY

Oh no 😥

Fridays order states it will be dispatched via carrier but there is no carrier dispatch information. Will be watching on Monday am with great interest.On the phone pm if there has been no movement.

My order from Tuesday is Inverness at present and I am hoping it will come over on the ferry Monday.

No emails from Connect or messages to date

Heres watching

Geoff

[geoff1]

Re: How to get to the top.

All that way up there to change a light bulb 😯

I needed the salts after watching that

Geoff

[geoff1]

Re: Invensys MPV01SV regulator

Update

Have been fitting 40ER101c19 instead of these invensys regulators with great success.

Only one problen to date was on a stoves cooker where the screw holding the facia on stopped the regulator fitting correctly. 😡 Ah well cannot win them all

Geoff

[geoff1]

Re: Diplomat ADP 8332

Hi

Have you checked to see if both spray arms are clean and turning freely? The best way to check if they are moving is to set them so they are facing front to back or side to side. Start the program off and after it sounds like it has started to wash carefully open the door to see if the spray arms have moved fromm the postion you set them at.
The chances are that they have not moved and the most likely cause of this is the wash/circulation motor.

HTH

Geoff

[geoff1]

Re: Amana American F/F reset

Had a look at their site where they have some general manuals listed

http://www.amana.co.uk/useguides.htm

In two of them they stated to hold the lock and water button in for 4 seconds until filter light turned green.

These units look very much like a Maytag unit I worked on not so long back 😕

HTH

Geoff

[geoff1]

Re: Maytag G32026PELB

Ian

I did one of these a while back and it was not a problem with fitting the board into the unit.
The problem comes when having to program it. I found the instructions to mine by removing the kickplate and searching in the small gap in the condensor area.
Without these for mine it would not start the unit up. Not sure if this the same in your case.

Geoff

[geoff1]

Re: At my wits end with a Tricity Bendix SIE514W oven

Hi

Original part number is 3111622027 or 506008303006 and state it is a ET51001/F5

Do not know what the difference between F5 and J5 types but connect do not interlink the zanussi and hotpoint number

HTH

Geoff

[Author]

Posts