Grendal

Forum Replies Created

Viewing 15 posts - 16 through 30 (of 165 total)
1 2 3 … 9 10 11
  • Author
    Posts
  • June 26, 2018 at 6:16 pm in reply to: sealed tub #456561
    Grendal
    Participant

    Re: sealed tub

    Haha he put the stability bracket on upside down 🙂

    June 18, 2018 at 8:50 pm in reply to: NEFF V6540XOGB/01 E 13 ERROR #456395
    Grendal
    Participant

    Re: NEFF V6540XOGB/01 E 13 ERROR

    Its a smeg built washer dryer. Check the dryer element isnt down to earth

    May 18, 2018 at 4:12 pm in reply to: Ignis ADL350/1 dishwasher pump only. #405064
    Grendal
    Participant

    Re: Ignis ADL350/1 dishwasher pump only.

    Its the control board fairly common fault

    April 3, 2018 at 7:25 pm in reply to: Gc2224gekb fridge freezer compressor cold #455126
    Grendal
    Participant

    Re: Gc2224gekb fridge freezer compressor cold

    Yes it will be the jazz board very common on those

    April 3, 2018 at 7:14 pm in reply to: Whirlpool F/F module #455070
    Grendal
    Participant

    Re: Whirlpool F/F module

    If I remember you can use 21 should work ok

    February 9, 2018 at 10:54 pm in reply to: hotpoint dryer heater reprogramming #453782
    Grendal
    Participant

    Re: hotpoint dryer heater reprogramming

    It is because there are 2 different manufacturers of elements that have different stats that work at different temperatures. If the element you are replacing is made by the same manufacturer there is no need to re programme it.

    January 18, 2018 at 5:07 pm in reply to: HPT W/D BHWD129 Had Module Fixed But…See Image #452947
    Grendal
    Participant

    Re: HPT W/D BHWD129 Had Module Fixed But…See Image

    Dryer ntc gives some very weird faults on these

    January 18, 2018 at 5:03 pm in reply to: Indesit IWB6123 #453181
    Grendal
    Participant

    Re: Indesit IWB6123

    Def a board fault had it a few times

    October 28, 2017 at 10:53 pm in reply to: Hotpoint tdwsf83bepuk #451216
    Grendal
    Participant

    Re: Hotpoint tdwsf83bepuk

    Just for info F01 is heater relay on the board. Personally I always replace the board and heater as a pair as you tend to get an F06 recall if you just change the board hope this helps

    October 22, 2017 at 3:25 pm in reply to: Jockey pulley burning out on Hotpoint/Indesit dryers #442908
    Grendal
    Participant

    Re: Jockey pulley burning out on Hotpoint/Indesit dryers

    They use the bpm motor on the higher end machines as it has a soft start They have been in use for at least a couple of years

    August 19, 2017 at 10:11 pm in reply to: Hotpoint BWD129 error codes please #449762
    Grendal
    Participant

    Re: Hotpoint BWD129 error codes please

    loads of problems with dryer ntc,s If it has a black one fitted change it as the new ones are white in colour

    August 5, 2017 at 12:20 am in reply to: Whirlpool MWN410M Microwave E5 #421991
    Grendal
    Participant

    Re: Whirlpool MWN410M Microwave E5

    Pretty sure it is the inverter board type usually the magnetron either mag down to earth or cracked magnets Whirlpool advise to change invertor board and mag as a pair pretty expensive repair

    August 5, 2017 at 12:16 am in reply to: Water filled weights? #449444
    Grendal
    Participant

    Re: Water filled weights?

    Whirlpool top loaders have used them for years no problems

    February 13, 2017 at 5:57 pm in reply to: Ignis dishwasher 854535015810 #445276
    Grendal
    Participant

    Re: Ignis dishwasher 854535015810

    Sounds like a blockage in the system, Check that the filters are clean and that the rubber hose underneath is not collapsing.

    February 8, 2017 at 5:52 pm in reply to: Whirlpool AWO/D 6528 Dead #445142
    Grendal
    Participant

    Re: Whirlpool AWO/D 6528 Dead

    You need to check the 12 nc as it is not listed on wedoc ;you very possibly have the wrong board

  • Author
    Posts
Viewing 15 posts - 16 through 30 (of 165 total)
1 2 3 … 9 10 11