Grendal

Forum Replies Created

Viewing 15 posts - 31 through 45 (of 165 total)
1 2 3 4 … 9 10 11
  • Author
    Posts
  • February 4, 2017 at 5:44 pm in reply to: Fisher & Paykel RF610A f26 #445025
    Grendal
    Participant

    Re: Fisher & Paykel RF610A f26

    Not sure what the code is but the wires at the top of the hinge break for fun

    February 2, 2017 at 2:09 pm in reply to: Whirlpool AWZ514D #444959
    Grendal
    Participant

    Re: Whirlpool AWZ514D

    It is the door lock saying that 9 times out of 10 any faults on those is the board

    February 1, 2017 at 5:02 pm in reply to: Whirlpool T/L service light on? #444937
    Grendal
    Participant

    Re: Whirlpool T/L service light on?

    Seen a few of these tbh they are quite a straight forward machine with no real problems. You can get a leak through thelid seal which can throw up a random f23 but when you switch it back on it will clear itself

    February 1, 2017 at 4:55 pm in reply to: Whirlpool AWZ514D #444957
    Grendal
    Participant

    Re: Whirlpool AWZ514D

    Its a meloni built machine I dont have any fault codes for it tbh I dont think it uses them

    February 1, 2017 at 4:50 pm in reply to: Whirlpool AWO/D6042 not spinning #444963
    Grendal
    Participant

    Re: Whirlpool AWO/D6042 not spinning

    Check that the pulley is not loose ,if that is ok it will be the control board

    January 9, 2017 at 7:14 pm in reply to: Admiral fridge freezer #444307
    Grendal
    Participant

    Re: Admiral fridge freezer

    Hi that machine is a standard Whirlpool side by side. The baffles do fail on those plus I have had the solenoid on the ice maker (The 1 inside the freezer compartment ) go faulty causing the board to blow on quite a few occaisions.

    December 21, 2016 at 3:18 pm in reply to: Ignis AKL907 Child lock on and can’t release #443942
    Grendal
    Participant

    Re: Ignis AKL907 Child lock on and can’t release

    It will req a new display board pt no is 481213018696 Display Ampere

    December 20, 2016 at 3:01 pm in reply to: Whirlpool Adg4700 #443920
    Grendal
    Participant

    Re: Whirlpool Adg4700

    Inadequate water supply, looking at the diagrams it is not a whirlpool built machine

    December 16, 2016 at 7:28 pm in reply to: Prima (Whirlpool) LPR602 pumping in short bursts #443236
    Grendal
    Participant

    Re: Prima (Whirlpool) LPR602 pumping in short bursts

    You can replace the motor without replacing the heater

    November 23, 2016 at 5:35 pm in reply to: Whirlpool Microwave F05 #443084
    Grendal
    Participant

    Re: Whirlpool Microwave F05

    It is usually the magnetron that is faulty either down to earth or the magnet is cracked ,either way Whirlpool advise to change the magnetron and board as a pair

    November 22, 2016 at 4:32 pm in reply to: Kingswood/Whirlpool KFID60A dishwasher #443033
    Grendal
    Participant

    Re: Kingswood/Whirlpool KFID60A dishwasher

    F4 = no drain, If it is draining it will probably be the wash pump motor as it monitors the current drawn by the motor to detect when it is empty or full

    November 11, 2016 at 9:52 pm in reply to: ignis ADL934S 854593415750 3 FLASHES ERROR #442709
    Grendal
    Participant

    Re: ignis ADL934S 854593415750 3 FLASHES ERROR

    F03 is a heater fault ….but check the wiring loom as its a very common fault

    November 11, 2016 at 5:39 pm in reply to: Whirlpool S25DRS33-A/G (858616815011) #442687
    Grendal
    Participant

    Re: Whirlpool S25DRS33-A/G (858616815011)

    Hi
    I would check to make sure that there is no ice build up on the return vent in the freezer, this is located behind the back panel on the right hand side near the defrost tray. Failing that is the fridge door closing properly as that will cause the diffuser to ice up and stop the fridge getting cold. I have never had to change a sensor in a side by side as they are pretty bullet proof

    November 11, 2016 at 5:33 pm in reply to: whirlpool dishwasher #442699
    Grendal
    Participant

    Re: whirlpool dishwasher

    Hi it will be the control board pt no is 480140102618 programmed board

    November 7, 2016 at 5:08 pm in reply to: Whirlpool Dishwasher ADG7800/2 8511 764 15780 #442503
    Grendal
    Participant

    Re: Whirlpool Dishwasher ADG7800/2 8511 764 15780

    Its a drain related problem or if it is draining ok check the O.W.I. which in in the sump on the right hand side it could be dirty

  • Author
    Posts
Viewing 15 posts - 31 through 45 (of 165 total)
1 2 3 4 … 9 10 11