Grendal

Forum Replies Created

Viewing 15 posts - 46 through 60 (of 165 total)
  • Author
    Posts
  • in reply to: Whirlpool Awz510e water tap light #441777
    Grendal
    Participant

    Re: Whirlpool Awz510e water tap light

    That is a meloni made machine, check continuity through all the valves as it fills through the prewash first

    in reply to: Maytag MTD09WH F07 #441749
    Grendal
    Participant

    Re: Maytag MTD09WH F07

    Hi it is just a Whirlpool dryer badged up. Fo7 is caused by the broken belt.
    To clear the fault turn the dial to 6 oclock position and press the start button 3 times then move dial 1 position clockwisse and press the start button 3 times again

    in reply to: Whirlpool ADP Dishwasher #441470
    Grendal
    Participant

    Re: Whirlpool ADP Dishwasher

    The motor is the favourite. The pcb monitors the current drawn by the motor to control the fill level. If the motor is seized it will abort the program

    in reply to: Whirlpool FRBB36af20/2 fridge warm #439538
    Grendal
    Participant

    Re: Whirlpool FRBB36af20/2 fridge warm

    If the flap is iced up you will need a diffuser plus check to ensure that the fridge door is closing properly as that is the usual cause (allowing warm air into the fridge )

    in reply to: Whirlpool ARZ740S ice maker leaking #433295
    Grendal
    Participant

    Re: Whirlpool ARZ740S ice maker leaking

    Willing to bet next weeks wages they are wrong 🙂 🙂

    in reply to: Argos advert #433154
    Grendal
    Participant

    Re: Argos advert

    Whirlpool bought Indesit to get a foot hold into the Russian market as Indesit are quite big there and they want to take a bigger stake in the other east European countries. The UK is a very very small part of their business hence they never replaced their Uk warehouse when Paddock wood burnt down

    in reply to: Whirlpool ARZ740S ice maker leaking #433293
    Grendal
    Participant

    Re: Whirlpool ARZ740S ice maker leaking

    The valve is fed from the rear board would need the 85 number to get part number

    in reply to: Ikea Microwave MW A12 S #432003
    Grendal
    Participant

    Re: Ikea Microwave MW A12 S

    That is a stuck button on the front. Make sure all buttons are free if they are then it will need a new board pt no is 480120101506

    in reply to: Weekend drudgery :( #431869
    Grendal
    Participant

    Re: Weekend drudgery 🙁

    Changed many an ocv 🙂 🙂

    in reply to: Electrolux washer dryer dead EWX14450W #431708
    Grendal
    Participant

    Re: Electrolux washer dryer dead EWX14450W

    Make sure the dryer element is not down to earth as this can cause this fault

    in reply to: Whirlpool to do a recall on Hotpoint dryers #431052
    Grendal
    Participant

    Re: Whirlpool to do a recall on Hotpoint dryers

    Not heard anything about this and at the moment Whirlpool and Hotpoint are being run as separate companies. Whirlpool are only taking on the Hotpoint washer dryer and 45cm dishwasher

    in reply to: Whirlpool drum lifters? #430889
    Grendal
    Participant

    Re: Whirlpool drum lifters?

    Hi Jim pt number is 480111104173 no screws holding them in they just slot in like the Hotpoint ones h.t.h

    in reply to: Whirlpool AKP262/1X Oven not working #430747
    Grendal
    Participant

    Re: Whirlpool AKP262/1X Oven not working

    It will need a display board pt no is 481213018696. It is quite a common fault on that model. No reset possible I’m afraid

    in reply to: Whirlpool ADG7790 (851177915810) F2 error #429719
    Grendal
    Participant

    Re: Whirlpool ADG7790 (851177915810) F2 error

    Thats the part they get gunged up

    in reply to: Whirlpool ADG7790 (851177915810) F2 error #429717
    Grendal
    Participant

    Re: Whirlpool ADG7790 (851177915810) F2 error

    Check the diaphragm switch also it should pump for approx 60 ” when you first select a program. Make sure the pump is not jammed

Viewing 15 posts - 46 through 60 (of 165 total)