hilly

Forum Replies Created

Viewing 15 posts - 76 through 90 (of 287 total)
  • Author
    Posts
  • in reply to: Indesit is70c not reversing #346402
    hilly
    Participant

    Re: Indesit is70c not reversing

    Many thanks 😉

    in reply to: whirlpool 6th sense #341601
    hilly
    Participant

    Re: whirlpool 6th sense

    leavemetogetonwithit wrote:Recently had this caused by low carbons – maybe need to look see if there’s one sticking.
    Mike.

    cheers it was the brushes 😳 i replaced them not long ago so neglected to check them 😳 com worn them out already new motor req,
    many thanks paul

    in reply to: hotpoint hob 6343p #338901
    hilly
    Participant

    Re: hotpoint hob 6343p

    Yes i did
    many thanks

    Paul

    in reply to: hotpoint hob 6343p #338899
    hilly
    Participant

    Re: hotpoint hob 6343p

    Cheers for the replies, I’ll go and have a play with it! As there was no leaflet with it I assumed it would be like for like but guess not.

    Cheers paul

    in reply to: bosch dryer #333930
    hilly
    Participant

    Re: bosch dryer

    gandh1 wrote:bit obvious but have you reset the resettable stat ????

    yeah cheers theres 2 on the back of this mod, both ok!

    in reply to: bosch dryer #333926
    hilly
    Participant

    Re: bosch dryer

    loopey wrote:wtv74103gb FD8804200525

    1st light (drying ) and 4th light (anti crease) are flashing after 1 minute
    there is no heat ? new heater fitted and front themister.. and has any one
    have the fault codes for these machines ?

    thanks in advance phil

    did you sort this problem out cos ive got one doing the same???
    baffled me!

    in reply to: academy pgl640blue #337050
    hilly
    Participant

    Re: academy pgl640blue

    ANDYVIVO wrote:Hi Paul
    The only units we know of are manufactured by Whirlpool. Is there a 12nc / service number?
    Andy

    the only numbers listed were the s/no and mod no 😥 seems ashame cos its imaculate for its age (bout 10yrs)

    cheers paul

    in reply to: hotpoint eg900x #335019
    hilly
    Participant

    Re: hotpoint eg900x

    geoff1 wrote:HI
    Just a question but from my rather faded memory does the cut not operate when the temerature of the oven gets to 75c which in turn will than power the fan.

    Maybe the old memory box is wrong?? but worth a check

    Geoff
    yes i expected that to hapen ive had it on full temp for 15 mins but it still dosent come on?

    cheers geoff1

    in reply to: creda concept halogen cooker 48345 #332618
    hilly
    Participant

    Re: creda concept halogen cooker 48345

    thanks for the replies, i went through everything but missed that the light bulb wasnt working, replaced bulb and hey presto job done 😳 😳

    thanks again

    in reply to: leisure range, EB10CRX #333392
    hilly
    Participant

    Re: leisure range, EB10CRX

    cheers that got me sorted 😀

    in reply to: bendix biw125w #331592
    hilly
    Participant

    Re: bendix biw125w

    leavemetogetonwithit wrote:This thread looks very much like it.
    Mike.

    cheers well going by geoff1’s findings i will try a motor first 😀

    thanks paul

    in reply to: stoves 720ef #331042
    hilly
    Participant

    Re: stoves 720ef

    cheers 😉

    in reply to: bosch wae24162gb/03 #330297
    hilly
    Participant

    Re: bosch wae24162gb/03

    definatly connected to cold, i changed the ntc with no joy, then quoted her for pcb which is just short of £80 which i thought was worth spending on a 3yr old bosh, but she decided to go out and buy a indesit 😯

    cheers for the replies

    in reply to: bosch single oven hbn730550b/04 #330249
    hilly
    Participant

    Re: bosch single oven hbn730550b/04

    any advice? 😥

    in reply to: bosch single oven hbn730550b/04 #330248
    hilly
    Participant

    Re: bosch single oven hbn730550b/04

    or does anyone have a wiring diagram for this plz?

    paul

Viewing 15 posts - 76 through 90 (of 287 total)