HotDog

Forum Replies Created

Viewing 15 posts - 331 through 345 (of 397 total)
1 2 3 … 22 23 24 25 26 27
  • Author
    Posts
  • October 14, 2009 at 5:34 pm in reply to: widl 126 dead #299513
    HotDog
    Participant

    Re: widl 126 dead

    board fault 😥

    May 26, 2009 at 5:45 pm in reply to: bosch wae24162uk/01 #287878
    HotDog
    Participant

    Re: bosch wae24162uk/01

    so would an open circuit heater cause no motor action

    May 26, 2009 at 11:16 am in reply to: Hotpoint WD420 Door locking but no door lock light #287538
    HotDog
    Participant

    Re: Hotpoint WD420 Door locking but no door lock light

    motor brushes worn out gives this fault

    March 31, 2009 at 8:37 pm in reply to: hotpoint wd440p F03 FAULT #281861
    HotDog
    Participant

    Re: hotpoint wd440p F03 FAULT

    i never found ntc faulty always fitted board to cure fault

    March 31, 2009 at 8:30 pm in reply to: Hotpoint wf540 #281905
    HotDog
    Participant

    Re: Hotpoint wf540

    check console module possible button /switch sticking also check motor brushes before fitting board

    February 25, 2009 at 10:06 pm in reply to: bosch d/w model srs4302gb/02 #278476
    HotDog
    Participant

    Re: bosch d/w model srs4302gb/02

    cheers thanks for info 😆

    January 6, 2009 at 8:17 pm in reply to: creda excell #273106
    HotDog
    Participant

    Re: creda excell

    remove belt then spin drum by hand should sound smooth just like spining a bike wheel if it grinds then bearing are your problem suspension does not cause problems yes you do have to remove front to to fit them

    December 23, 2008 at 6:27 pm in reply to: WIRING DIAGRAM FOR CREDA DRYER 37643 #271864
    HotDog
    Participant

    Re: WIRING DIAGRAM FOR CREDA DRYER 37643

    do you have fax can send copy unable to scan could post you a copy

    December 17, 2008 at 8:59 pm in reply to: teknic dishwasher dw2677/1 #271747
    HotDog
    Participant

    Re: teknic dishwasher dw2677/1

    thanks for info also found your post on the net is the water indicator removed underneath by a slight twist

    December 17, 2008 at 8:46 pm in reply to: Hotpoint WD440G #271824
    HotDog
    Participant

    Re: Hotpoint WD440G

    Yes this is normal for induction motors it is normal to strap 0volts to earth to remove induction and of course 0volts is black cable if removed inductance can create strange faults.

    December 10, 2008 at 9:36 pm in reply to: Hotpoint FDW60 dishwasher. #263922
    HotDog
    Participant

    Re: Hotpoint FDW60 dishwasher.

    faulty ring nut seal were upper spray arm locates on back

    August 1, 2008 at 7:48 pm in reply to: Hotpoint BFI620 DW LED 2 + 4 #256015
    HotDog
    Participant

    Re: Hotpoint BFI620 DW LED 2 + 4

    Check the make of the heater if it not a made by bleckmann change it t

    March 25, 2008 at 9:41 pm in reply to: WF860 30 mins to 37. #246442
    HotDog
    Participant

    Re: WF860 30 mins to 37.

    I lad tha knows its takes a while to catch on these days

    March 19, 2008 at 10:38 pm in reply to: WF860 30 mins to 37. #246440
    HotDog
    Participant

    Re: WF860 30 mins to 37.

    these boards dont get the wash time exactley right and will extend the time to compensate but your diagnioses could also be correct

    March 19, 2008 at 7:49 pm in reply to: WF860 30 mins to 37. #246438
    HotDog
    Participant

    Re: WF860 30 mins to 37.

    Hi Jim does it finish the prog or does it keep going bacc to 37min

  • Author
    Posts
Viewing 15 posts - 331 through 345 (of 397 total)
1 2 3 … 22 23 24 25 26 27