HotDog

Forum Replies Created

Viewing 15 posts - 346 through 360 (of 397 total)
1 2 3 … 23 24 25 26 27
  • Author
    Posts
  • March 16, 2008 at 9:30 pm in reply to: Hotpoint WF860 completing program & starting again !! #245929
    HotDog
    Participant

    Re: Hotpoint WF860 completing program & starting again !

    this machine can start part of the prog again if it has completed the prog to soon – had same fault. does it do complete prog again or does it just extend time? if so there is no fault

    February 25, 2008 at 8:39 pm in reply to: WMA46 BOARD #244002
    HotDog
    Participant

    Re: WMA46 BOARD

    Also check motor plug for carbon dust build up will cause short

    January 17, 2008 at 10:11 pm in reply to: HOTPOINT DISHWASHER #239937
    HotDog
    Participant

    Re: HOTPOINT DISHWASHER

    Then you do the okey cokey and you turn around

    December 6, 2007 at 7:49 pm in reply to: been to H/point CTD00G con’d drier. Not Drying Clothes?. #234192
    HotDog
    Participant

    Re: been to H/point CTD00G con’d drier. Not Drying Clothes?.

    Did you check for blockage from condensor box to pump

    December 6, 2007 at 7:42 pm in reply to: Hotpoint auto WF860 #236422
    HotDog
    Participant

    Re: Hotpoint auto WF860

    Have you checked sump for blockage

    December 2, 2007 at 9:36 pm in reply to: tdl30 hotpoint dryer #235902
    HotDog
    Participant

    Re: tdl30 hotpoint dryer

    Better with pulleys i have done this mod with great results

    November 7, 2007 at 8:55 pm in reply to: noisy is70c indesit condenser dryer #233225
    HotDog
    Participant

    There is a new fixing clip to stop rear fan coming loose ,a bit stonger than existing fixing,,

    November 7, 2007 at 8:46 pm in reply to: noisy is70c indesit condenser dryer #233224
    HotDog
    Participant

    Re: noisy is70c indesit condenser dryer

    There is a fault with rear fixing clip not holding fan tight new clip has been modified to cure problem

    October 22, 2007 at 6:23 pm in reply to: Hotpoint WT5401p #231281
    HotDog
    Participant

    Re: Hotpoint WT5401p

    I like it theres more than one way to skin a cat 8) 8)

    October 21, 2007 at 8:27 pm in reply to: Hotpoint WF541 #231603
    HotDog
    Participant

    Re: Hotpoint WF541

    Had simlar fault last week fitted pump and board came up with f02 found broken wiring to motor plug

    October 21, 2007 at 8:09 pm in reply to: Hotpoint WT5401p #231279
    HotDog
    Participant

    Re: Hotpoint WT5401p

    There is another way buy a new machine £169 +vat trade remove container for your job charge £100 you are then left with motor/module /ect for stock do the maths it is possible if you can use all the spare parts your left with food for thought

    September 27, 2007 at 8:03 pm in reply to: Hotpoint…WT965A..ser.no. 606140041 #228755
    HotDog
    Participant

    Re: Hotpoint…WT965A..ser.no. 606140041

    remove console module contacts and refit checking good connection common fault

    August 30, 2007 at 5:58 pm in reply to: Hotpoint 1604321 module #226028
    HotDog
    Participant

    Re: Hotpoint 1604321 module

    Hi jim can confirm 1604321 is correct for your first code number not sure of the next one will see if i can find info on this 🙂 🙂

    August 5, 2007 at 8:37 pm in reply to: Hotpoint Washing Machine Mod. WF740 #223059
    HotDog
    Participant

    Re: Hotpoint Washing Machine Mod. WF740

    Check pump/filter for blockage can cause back pressure if ok board faulty they nearly always are 😆

    February 15, 2007 at 8:18 pm in reply to: Hotpoint DWF70 despair #204254
    HotDog
    Participant

    Re: Hotpoint DWF70 despair

    Just another day in the life as as a service engineer thats one of the reasons why i specialise in hotpoint/creda i can stock all parts whith no fear of being stuck with unused spares sorry i could not be more positive better luck next time eh 😥

  • Author
    Posts
Viewing 15 posts - 346 through 360 (of 397 total)
1 2 3 … 23 24 25 26 27