HotDog

Forum Replies Created

Viewing 15 posts - 121 through 135 (of 397 total)
1 2 3 … 8 9 10 … 25 26 27
  • Author
    Posts
  • April 10, 2015 at 8:09 pm in reply to: white knight cl767 belt #426407
    HotDog
    Participant

    Re: white knight cl767 belt

    ye after 40years i am getting fussy what i do

    April 9, 2015 at 8:46 pm in reply to: white knight cl767 belt #426405
    HotDog
    Participant

    Re: white knight cl767 belt

    thats what i needed to know thanks jim not that desprate for a job

    April 4, 2015 at 9:41 am in reply to: whirpool awod as 147 #426244
    HotDog
    Participant

    Re: whirpool awod as 147

    thanks will give it a try

    April 3, 2015 at 6:26 pm in reply to: whirpool awod as 147 #426242
    HotDog
    Participant

    Re: whirpool awod as 147

    sorry it wa coming up service not f05

    March 31, 2015 at 9:30 pm in reply to: Hotpoint IDCS845UK (Dryer) #426134
    HotDog
    Participant

    Re: Hotpoint IDCS845UK (Dryer)

    yes jim i learned my lesson tried 3 all failed gen only now

    March 30, 2015 at 6:35 pm in reply to: Hotpoint IDCS845UK (Dryer) #426131
    HotDog
    Participant

    Re: Hotpoint IDCS845UK (Dryer)

    yes was it none gen by any chance

    March 17, 2015 at 8:14 pm in reply to: indesit IWE91281 eco. #425615
    HotDog
    Participant

    Re: indesit IWE91281 eco.

    pressure switches are known to cause problems also it does a short intial fill stops then changes to the other valve to fill to correct level think you prob already know that, never had any luck with reset myself

    March 8, 2015 at 8:38 pm in reply to: zanussi zwg1120m #425388
    HotDog
    Participant

    Re: zanussi zwg1120m

    thanks dave and jim

    February 13, 2015 at 6:14 pm in reply to: HPT BWM129 Module replacement #424689
    HotDog
    Participant

    Re: HPT BWM129 Module replacement

    straight swap

    February 4, 2015 at 7:53 pm in reply to: HTP x2 WMUD 962 942 Pressure switch reset #424343
    HotDog
    Participant

    Re: HTP x2 WMUD 962 942 Pressure switch reset

    If you have the card/reader then give it a try

    February 3, 2015 at 8:42 pm in reply to: HTP x2 WMUD 962 942 Pressure switch reset #424338
    HotDog
    Participant

    Re: HTP x2 WMUD 962 942 Pressure switch reset

    sometimes you have to set and leave the machine for upto an hour and they can then start to work,but if that fails you need hotpoint to re-prog the board, but to be honest its never worked for me dont waste anymore time on it forget changing p/sw

    January 29, 2015 at 9:50 pm in reply to: beko dryer model drc68c tripping elec #424162
    HotDog
    Participant

    Re: beko dryer model drc68c tripping elec

    Thanks i should have mentioned the customer has kept the condensor very clean it only trips after about 15 min then whe you remove back panel its full of moisture done loads of same problem on hotpoint which i have fixed no problem by cleaning and clearing pump/condensor,i know its a basic problem just cannot see why on this one

    January 9, 2015 at 6:54 pm in reply to: Hotpoint wmpf742 cracked chassis #423377
    HotDog
    Participant

    Re: Hotpoint wmpf742 cracked chassis

    had one to day cracked base 2 years old wml520

    January 9, 2015 at 6:51 pm in reply to: Motor speeds up and slows down on spin Candy 1682D #423421
    HotDog
    Participant

    Re: Motor speeds up and slows down on spin Candy 1682D

    The heater can cause spin problems

    December 29, 2014 at 6:50 pm in reply to: LG 11kg load, who knows anything about these? #364656
    HotDog
    Participant

    Re: LG 11kg load, who knows anything about these?

    I only know LG had lots of drums failing on the early 11kg machines i did see lots of these scrapped and replaced by LG they were similar to the hotpoint/indesit ones that collapsed didnt see the damper on them but you prob heard about that fault

  • Author
    Posts
Viewing 15 posts - 121 through 135 (of 397 total)
1 2 3 … 8 9 10 … 25 26 27