hotpnt

Forum Replies Created

Viewing 14 posts - 706 through 719 (of 719 total)
1 2 3 … 46 47 48
  • Author
    Posts
  • March 29, 2007 at 4:05 pm in reply to: Hpt Motor Conversion Problem. #209228
    hotpnt
    Participant

    Re: Hpt Motor Conversion Problem.

    plus the fhp motor is alot longer & can hit the side mounted pressure switch very easily

    March 29, 2007 at 4:04 pm in reply to: Hotpoint WD860 Dryer no heat #205058
    hotpnt
    Participant

    Re: Hotpoint WD860 Dryer no heat

    there have been 3 heater boxes,

    March 29, 2007 at 3:38 pm in reply to: Hotpoint WD860 Dryer no heat #205056
    hotpnt
    Participant

    Re: Hotpoint WD860 Dryer no heat

    only the dryer fan may be loose, or the fixing spinning within the fan

    March 29, 2007 at 3:21 pm in reply to: INDESIT DISHWASHER IDE1000 UK 2 #209261
    hotpnt
    Participant

    Re: INDESIT DISHWASHER IDE1000 UK 2

    hi, any fault to earth on the heater can be recognised by the module as a valve fault

    March 28, 2007 at 9:37 pm in reply to: Hotpoint WF430 Bearing Kit #209063
    hotpnt
    Participant

    Re: Hotpoint WF430 Bearing Kit

    hi phidom, what was the problem with fitting the bearings?,

    March 28, 2007 at 9:34 pm in reply to: Hotpoint WF430 Bearing Kit #209062
    hotpnt
    Participant

    Re: Hotpoint WF430 Bearing Kit

    yep the 1605082 is the rear half with heater,

    March 28, 2007 at 9:17 pm in reply to: Scale removers #209129
    hotpnt
    Participant

    Re: Scale removers

    hi, yes this is pretty good stuff & a good seller too, if you find a sludged up machine i usually recommend 2 sachets in 2 weeks then monthly, clears the drum well

    March 27, 2007 at 9:52 pm in reply to: Hotpoint WF430 Bearing Kit #209057
    hotpnt
    Participant

    Re: Hotpoint WF430 Bearing Kit

    Hi, the same rear half is used on wma and wf, the difference is in the electronics, its the same bearing kit also, what seems to not fit with the bearings?

    March 24, 2007 at 12:12 am in reply to: Indesit Franchise #174822
    hotpnt
    Participant

    Re: Indesit Franchise

    cheers,

    March 23, 2007 at 11:45 pm in reply to: Indesit Franchise #174820
    hotpnt
    Participant

    Re: Indesit Franchise

    hi guys, well im one of those fools!
    iof trying other brands like Bosch & Hoover, LG etc, cause ive seen the amount of electronics ei stuff are they all goint that way? are they really that different? and were is the best place to start up a trade spares account?

    March 23, 2007 at 8:56 pm in reply to: WF630 #208502
    hotpnt
    Participant

    Re: WF630

    hi, what was the reason for the need of a new supressor?

    March 23, 2007 at 8:38 pm in reply to: dryer ctd40 #208203
    hotpnt
    Participant

    Re: dryer ctd40

    hi, you may well have sorted this one by now, but just one point, on some of these the module puts the light on whenever the door is open as a reminder to empty the tank, so if the door lock is duff it will keep the light on and also make the whole machine ‘dead’. cause if it was really thinking the bottle was full it would still start up & run, just with no heat

    March 22, 2007 at 10:35 pm in reply to: Indesit DI620 D/washer #207958
    hotpnt
    Participant

    Re: Indesit DI620 D/washer

    hi, if you try to start a prog with the heater disconnected it should go straight into a fault mode sensing that the heater is OC, if it does not then this will prove a fault on the module,

    March 21, 2007 at 9:32 pm in reply to: Creda Condenser Dryer TCR2 How do I Remove the Top #208536
    hotpnt
    Participant

    Re: Creda Condenser Dryer TCR2 How do I Remove the Top

    HI, just 2 screws at the back of the lid, then pull back sharply, the side panel has 3 screws down the back & one half-way along underneath

  • Author
    Posts
Viewing 14 posts - 706 through 719 (of 719 total)
1 2 3 … 46 47 48