iadom

Forum Replies Created

Viewing 15 posts - 3,586 through 3,600 (of 25,656 total)
  • Author
    Posts
  • in reply to: df 61 tripping #424077
    iadom
    Moderator

    Re: df 61 tripping

    Should it actually be a Hotpoint machine I do have a copy of the manual if you want it.

    in reply to: Hotpoint stuck on drain? #424103
    iadom
    Moderator

    Re: Hotpoint stuck on drain?

    I suppose one other possibility in theory is the pressure switch sticking on overfill but can’t see how that could have happened, he didn’t tilt the machine to drain the pump. :con:

    in reply to: ise w1606 stuck filling and emptying on 11 mins #424100
    iadom
    Moderator

    Re: ise w1606 stuck filling and emptying on 11 mins

    Over soaping???

    in reply to: df 61 tripping #424075
    iadom
    Moderator

    Re: df 61 tripping

    I know it’s out of character but Martin is being sarcastic, and rather rude . :rolls:

    in reply to: df 61 tripping #424072
    iadom
    Moderator

    Re: df 61 tripping

    I wonder why people don’t give a make as well as a model. 🙁

    Hotpoint have a DF61 is this one of those? If it is then it’s a bog standard Bosch design with sealed base. Side panels off to access heater terminals etc.

    Also moved to correct forum, this is not a General Trade question.;)

    in reply to: Hotpoint WMUD 843PX UK – Cycle doesn’t complete #423922
    iadom
    Moderator

    Re: Hotpoint WMUD 843PX UK – Cycle doesn’t complete

    For the wiring between heater and pcb a simple continuity test, but you should have tested the element for continuity, resistance and insulation before you changed it. It is however pointing towards a main pcb failure or if you are very lucky a pressure switch fault.

    in reply to: Football Season 2014/2015 #417496
    iadom
    Moderator

    Re: Football Season 2014/2015

    Martin wrote:Be careful of what you wish for.

    in reply to: Football Season 2014/2015 #417494
    iadom
    Moderator

    Re: Football Season 2014/2015

    Well, well, well, United’s dismal draw at Cambridge looking like a good result now as SAINTS, SPURS, City and Chelsea all bombed out of the cup on their own grounds by lower teams..:rotfl:

    in reply to: Hotpoint WMUD 843PX UK – Cycle doesn’t complete #423920
    iadom
    Moderator

    Re: Hotpoint WMUD 843PX UK – Cycle doesn’t complete

    I gave you good advice in my last post but you make no mention of actually testing the heating element .
    Did you test the heater before you replaced it?

    If you do not have access to proper test equipment and the knowledge to use them you should not be putting your hands inside any piece of electrical equipment full stop.

    in reply to: EBAC washing machines launch in the spring #423858
    iadom
    Moderator

    Re: EBAC washing machines launch in the spring

    Au contraire, I have never, ever used the phrase ‘unicorn poo’ in respect of a machines quality. As I have already stated it is a stupid and incorrect term used by people too lazy to actually think about what they are writing, it should not be used to describe something of poor quality. As the Unicorn is a mythical beast if you really did have some Unicorn Poo it would be beyond value.

    Unicorn Poo means something does not exist, it does not mean it is rubbish. 😛

    iadom
    Moderator

    Re: Hotpoint dishwasher FDW80 – where is leak as rust on flo

    As I suspected, the leak was outside the dishwasher . 8)

    in reply to: EBAC washing machines launch in the spring #423856
    iadom
    Moderator

    Re: EBAC washing machines launch in the spring

    . What has been will be again,
    what has been done will be done again;
    there is nothing new under the sun.

    in reply to: EBAC washing machines launch in the spring #423851
    iadom
    Moderator

    Re: EBAC washing machines launch in the spring

    B*llocks, building machines with parts sourced outside the country goes on worldwide, and has done for fifty years or more in every branch of manufacturing. If they are employing people in this country to assemble them then more power to their elbow.

    in reply to: Hotpoint Washing Machine #423957
    iadom
    Moderator

    Re: Hotpoint Washing Machine

    mjhservices wrote: do you have the flashing lights error codes?

    Yes, and so do you.;)

    ERROR CODES THREAD

    in reply to: “Ooooh Matron” ? #165973
    iadom
    Moderator

    Re:

    Desperate Don, like it. :rotfl:

Viewing 15 posts - 3,586 through 3,600 (of 25,656 total)