Forum Replies Created
-
Posts
-
Re: Fault Code Guide subs update N/A?
I was just checking that all of my apps worked after the iOS.8 update and looked at random pages. On lots of them the letters rn or rnrn had been inserted into the text at various places.
Look at Amica, AWC with lcd, …..E54, several rn’s in that one. Or the Baumatic BDW13 Quick function test, that is littered with rn’s.
Jim.
Re: Fault Code Guide subs update N/A?
Just noticed that all the pages on the guide are full of rn, rnrn, or even rnrnrn’s all over the place. Has that just happened recently?
Jim.
Re: Hotpoint lft114 uk
I can get you the part numbers but have never found a customer stupid enough to pay for a PCB repair on one of these and have never had a smart card reader either. 🙁
Re: Hotpoint lft114 uk
It does need programming, pretty certain the port is at the front.
There are two different modules for this machine, also three smart cards not interchangeable.
Full serial number and commercial code needed to ID correctly.
Re: BF1680 dishwasher
How hard did you look? Perhaps if you had looked for a BFI ( for integrated ) and not a BF1. 😀
Looks like a classic heater or pcb fault. 🙁
Re: Hotpoint Ultima Wmud843p
A long shot but worth checking the wall socket or trying it in another socket if you can.
I once had the exact same fault due to a dodgy mains socket.
Re: Hotpoint FDW20 gone pop!
A close visual test is usually all that is needed, other possible causes are wiring harness faults, often inside the door.
It is a 100{e5d1b7155a01ef1f3b9c9968eaba33524ee81600d00d4be2b4d93ac2e58cec2d} Indesit machine with the pcb, heater and main motor all known weak areas. 🙁
Re: Hotpoint FDW20 gone pop!
First thing to check is the mains filter, close to where the mains cable enters the machine.
Sent from my iPad using Tapatalk HDRe: vtd00 drum scraping
Complete drum kit mod is C00145650, you must fit the 16mm rear foam seal in place of the original 26mm seal.
Re: More penny pinching.
eastlmark wrote:
Peveral owned maybe?
This is despite my hard sell to the managers on ISE machines
No idea who owns the place, they paid me in cash for resetting the TOC, tripped due to clogged condensor. :rolls:ISE sales will be even harder quite soon. 😉
Re: Hotpoint BWD129 bearing replacement
Not sure but I seem to think there are different sizes of shaft used, also some have an alloy spider, some a cast iron one.
Re: ctd 00 toc still tripping
If everything is completely clear and clean then the capacitor would be my guess. They will appear to start to tumble even if it is failing sometimes.
Easiest way to test is to remove the lid and try and hold the drum with one hand pressed against it, if the capacitor is failing then you will need very little pressure to hold the drum, if it is OK then it will be very hard to stop it from turning.
Re: are the modules interchangeable on the old wma hotpoints
I have just e mailed you the programming sheets, found your e mail address from a 2011 PM you sent me. 😉
Re: are the modules interchangeable on the old wma hotpoints
The one from a WMS38 will fit, just needs programming for a WMA40. Never really bothered to find out what the differences are as always fitted the correct one then programmed it to the model it was fitted into. Never had a shop or uplifted machines so didn’t build up a stock of used modules either.
As far as I know you cannot re code the different pcb’s to fit any WMA, only program them for the various models they are designed to fit.
Do you have the programming list for the 1604321 pcb, can send it you if you don’t.
Re: Football Season 2014/2015
Well it looked like money well spent today, fantastic atmosphere in the ground and a great reception for Rio. for a team with so many new players in the side United did play really well in midfield and attack. You could still have driven a coach and horses through their defence though, thankfully QPR came on a rocking horse. 😛
Far sterner tests await.
