johnmac11

Forum Replies Created

Viewing 15 posts - 886 through 900 (of 1,760 total)
  • Author
    Posts
  • in reply to: Whirlpool DW ADP4501/5WH No start #269591
    johnmac11
    Participant

    Re: Whirlpool DW ADP4501/5WH No start

    It could be a fill problem caused by either the water valve or drain pump being o/c. Or it could be a faulty door switch.
    If not it will probably be the PCB


    John

    in reply to: w/pool adg642 #270149
    johnmac11
    Participant

    Re: w/pool adg642

    Hi Cris,
    What part number did he fit?
    There are a lot of blank PCB’s for these appliances that need programming via a SAM module so it is possible he has one of these by mistake.


    John

    in reply to: Whirlpool ARC5070 Seal #269520
    johnmac11
    Participant

    Re: Whirlpool ARC5070 Seal

    These seals can be replaced but you will need to post the 12nc number from your fridge to identify the correct part number, there are 2 different types.

    The 12nc number can be found on the inner fridge wall next to the salad bins and starts with 8501507*****

    John

    in reply to: PRIMA OVEN (W/POOL) 857920515512 #269970
    johnmac11
    Participant

    Re: PRIMA OVEN (W/POOL) 857920515512

    Hi Ally
    Part number is 481245059578 you will also need a new modified hinge kit for this one, I need the serial number to confirm correct part number for the kit.

    John

    in reply to: Whirlpool FCSM6 Fan Oven not heating #269398
    johnmac11
    Participant

    Re: Whirlpool FCSM6 Fan Oven not heating

    part number is for a complete switch.

    John

    in reply to: Whirlpool double oven model AKZ161/03/IX 858516115122 #269887
    johnmac11
    Participant

    Re: Whirlpool double oven model AKZ161/03/IX 858516115122

    Just a thought, this might apply

    read this one.

    in reply to: Whirlpool double oven model AKZ161/03/IX 858516115122 #269886
    johnmac11
    Participant

    Re: Whirlpool double oven model AKZ161/03/IX 858516115122

    Probably is the power PCB but the original part number I have is 481221458307 which is superseded by 481231019121

    John

    in reply to: Whirlpool DW ADP4501/5WH No start #269588
    johnmac11
    Participant

    Re: Whirlpool DW ADP4501/5WH No start

    If there are two boards listed then the one that says “sam” is a blank board. Order the other and it should come programmed.

    John

    in reply to: whilpool dryer stats #269504
    johnmac11
    Participant

    Re: whilpool dryer stats

    I’ll take it it is the two on the heater you want, if so they come in a kit 481928228665


    John

    in reply to: Whirlpool FCSM6 Fan Oven not heating #269395
    johnmac11
    Participant

    Re: Whirlpool FCSM6 Fan Oven not heating

    Found it, looks like an Ikea special.

    If the centre button wont push in it will stop you from setting the clock and the display will always show stop, part number for button switch is 481241029352
    If it needs the fan oven element the part number is 481225998405.

    HTH


    John

    in reply to: Rumour/Proposed Vat drop #269326
    johnmac11
    Participant

    Re: Rumour/Proposed Vat drop

    Well it is official the Chancellor announced a cut to 15{e5d1b7155a01ef1f3b9c9968eaba33524ee81600d00d4be2b4d93ac2e58cec2d} starting from December 1 lasting for 13 months before returning to the present level of 17.5{e5d1b7155a01ef1f3b9c9968eaba33524ee81600d00d4be2b4d93ac2e58cec2d} on 1/1/2010

    Oh joy, must run out now and buy a new home cinema 😆

    John

    in reply to: Can I Just Say? #269355
    johnmac11
    Participant

    Re: Can I Just Say?

    too much real ale Chris??

    I cannot answer for the rest but I for the past 4 years have been office based and find that I cannot answer a lot of the posts with confidence. I have not looked at any other brand other than Whirlpool or F&P ( not AUS washers )for the last 12 years and would not be much good on the Smeg you mentioned below.

    I have in the past volunteered my services to help with editing articles and chaffing out spam posters but do not have admin rights to do this.

    If this in effect makes me deadwood then I believe Ken has the power to chop me if he wants…


    John

    in reply to: Rumour/Proposed Vat drop #269319
    johnmac11
    Participant

    Re: Rumour/Proposed Vat drop

    I would prefer it to stay at the 17.5{e5d1b7155a01ef1f3b9c9968eaba33524ee81600d00d4be2b4d93ac2e58cec2d} rate for two reasons
    Firstly we will have the hassle of two different VAT rates in one quarter ( I can hear my accountant chuckling ):lol: and second but most the most important reason is suppliers will stealthily raise their prices,..

    Call me a cynic


    John

    in reply to: whirlpool cooker #269051
    johnmac11
    Participant

    Re: whirlpool cooker

    If you have the main oven knob switched to off and the centre button is working correctly then it will probably be the main pcb.


    John

    in reply to: whirlpool cooker #269049
    johnmac11
    Participant

    Re: whirlpool cooker

    Is the centre push button working, these are known to jam solid

    John

Viewing 15 posts - 886 through 900 (of 1,760 total)