johnmac11

Forum Replies Created

Viewing 15 posts - 1,186 through 1,200 (of 1,760 total)
  • Author
    Posts
  • in reply to: Whirlpool AWZ541 T/D #214828
    johnmac11
    Participant

    Re: Whirlpool AWZ541 T/D

    Costly one this one, the only way to cure it is to fit a new motor.
    About £100 retail


    John

    johnmac11
    Participant

    Re: Whirlpool American Fridge Freezer broken down – help!

    As Gegsy said the rear board is the usual culprit in this case so I would fit that first. I have saw a few where it takes both boards to rectify the problem 🙁 .


    John

    in reply to: whirlpool awm 321 #214765
    johnmac11
    Participant

    Re: whirlpool awm 321

    481225928672 is the heater for the early Delta machines and has a NTC fitted. The AWM321 has no NTC and the temp is controlled by a seperate stat.
    There are two different heaters for this appliance, you need the 12nc number to be sure which one.


    John

    in reply to: BAUMATIC #214715
    johnmac11
    Participant

    Re: BAUMATIC

    Is it this one??

    http://www.ukwhitegoods.co.uk/modules.p … ght=sm90px


    John

    in reply to: F & P Fridge/freezer #214679
    johnmac11
    Participant

    Re: F & P Fridge/freezer

    If it is the one with the fridge at the top all you do is pull off the back panel. pull off small panel at bottom/back of fridge and remove foam cover to access the fan, no tools needed.


    John

    PS: check your mail

    in reply to: Christmas 2007 #206626
    johnmac11
    Participant

    Re: Christmas 2007

    kwatt wrote:The main event is the Saturday night but some people (John Mac etc.) like to get in a little more drinking time

    I will admit to having a couple of shandys with Dave on the Friday night, isnt it amazing how fit the women looked after our respective better halfs went to bed. :rotfl:

    BTW The only reason I went up on the Friday was to give Dave a lift from the airport to the hotel, Honest….


    John

    in reply to: wpl awm8123 #213308
    johnmac11
    Participant

    Re: wpl awm8123

    10 different versions of that machine, have you got the 12nc

    John

    in reply to: wpl awm8123 #213306
    johnmac11
    Participant

    Re: wpl awm8123

    Is it the clear plastic cover between the module and the fascia ?
    If so then it comes complete with the module.


    John

    in reply to: Miele cat and dog TT5000 #213435
    johnmac11
    Participant

    Re: Miele cat and dog TT5000

    don wrote:it looks like a sealed unit to me

    Thanks Don, the thread is wrapped round one of the bearings and is refusing to shift. I can turn the end cap round 360 degrees but cannot see how it dismantles. 👿

    John

    in reply to: WPL AWM5125 Spider #213461
    johnmac11
    Participant

    Re: WPL AWM5125 Spider

    Sold as a complete inner drum only

    John

    in reply to: Welcome To The War Room #118147
    johnmac11
    Participant

    kwatt wrote:Time for me to have a little fun. 😈

    What are you up to? heard a rumor that you were going to invite Yurgen and Mike the Bike in here. 😆

    John

    in reply to: Whirpool oven #213433
    johnmac11
    Participant

    Re: Whirpool oven

    Turn the main oven knob to the off position
    Press small centre button till digits lights up in bottom r/h corner of display
    Turn right hand knob to adjust to correct time
    Press centre knob to set
    Oven should work normaly now

    John

    in reply to: Whirlpool Technical. #212468
    johnmac11
    Participant

    Re: Whirlpool Technical.

    happycack wrote:3RAWZ481E to be precise.

    The full number wont go into SIOS, if you are looking for this model miss out the “3R” part.

    Fuse is a 8A 20mm glass fuse.


    John

    in reply to: Whirlpool Technical. #212466
    johnmac11
    Participant

    Re: Whirlpool Technical.

    If it is an AWZ481 take the top off and go to the l/h side looking from the front, there is a fuse in the harness below the metal plate.


    John

    in reply to: Sale of Dangerous Parts to the Public. #176899
    johnmac11
    Participant

    Re: Sale of Dangerous Parts to the Public.

    Headlines from Gas Installer magazine today say that Parts center will no longer sell any gas related part to a non Corgi registered customer. I Take it you will need to show your card to buy parts in future.


    John

Viewing 15 posts - 1,186 through 1,200 (of 1,760 total)