Lawrence

Forum Replies Created

Viewing 15 posts - 91 through 105 (of 2,138 total)
1 2 3 … 6 7 8 … 141 142 143
  • Author
    Posts
  • January 30, 2018 at 7:19 pm in reply to: February 2018 WTA conference #451185
    Lawrence
    Participant

    Re: February 2018 WTA conference

    Thanks Barry looking in to link now
    have you registered on eventbrite ?

    January 26, 2018 at 8:41 am in reply to: Samsung heat Pump dryer fan required #453371
    Lawrence
    Participant

    Re: Samsung heat Pump dryer fan required

    LF Parts sometimes have Samsung stuff that no one else does

    January 25, 2018 at 4:44 pm in reply to: WT960P Hotpoint #453353
    Lawrence
    Participant

    Re: WT960P Hotpoint

    Thanks Jim

    January 24, 2018 at 1:57 pm in reply to: Beko floppy door handle #453345
    Lawrence
    Participant

    Re: Beko floppy door handle

    It needs a new handle

    January 24, 2018 at 9:02 am in reply to: Work required – midlands #443332
    Lawrence
    Participant

    Re: Work required – midlands

    Agree with Jim ,if you can get to the conference I would thoroughly recommend it, as there are more networking opportunities than anywhere else

    January 17, 2018 at 10:02 am in reply to: Samsung WF8604 bearing job #453184
    Lawrence
    Participant

    Re: Samsung WF8604 bearing job

    whoops my bad – spider -DC9715184A , rear half DC9715236B
    both from connect so check them for prices , about an hour to do the job

    January 17, 2018 at 7:39 am in reply to: Samsung WF8604 bearing job #453182
    Lawrence
    Participant

    Re: Samsung WF8604 bearing job

    Rear half unless you can match bearings and seals
    Spider comes on inner drum

    January 12, 2018 at 8:31 pm in reply to: RSG5UCRS ice route cover #452998
    Lawrence
    Participant

    Re: RSG5UCRS ice route cover

    display cover off is the only way to do it

    January 11, 2018 at 8:54 am in reply to: February 2018 WTA conference #451183
    Lawrence
    Participant

    Re: February 2018 WTA conference

    What Martin is kindly pointing out is that in 5 weeks time in one place there will be Spares suppliers , Work providers, Manufacturers , Appliance Wholesalers, Software Suppliers all under one roof.
    So for those that complain about spares prices, Lack of work ,Attitude of manufacturers , lack of call handling software and new machine prices, should you be there ?

    January 5, 2018 at 7:32 am in reply to: Rangemaster oven not heating #452795
    Lawrence
    Participant

    Re: Rangemaster oven not heating

    Test the continuity of the little white toc next to the element terminals

    January 4, 2018 at 4:03 pm in reply to: Bush AE6BSW oven #452772
    Lawrence
    Participant

    Re: Bush AE6BSW oven

    Normally the selector , but Bush parts can be tricky to obtain

    January 3, 2018 at 10:26 am in reply to: BT2710SS loss of power #452680
    Lawrence
    Participant

    Re: BT2710SS loss of power

    Hi Andy
    I’m in Ipswich
    Ring my office on 01473233533

    December 29, 2017 at 3:06 pm in reply to: Smeg cooker hood light fitting replacement #452640
    Lawrence
    Participant

    Re: Smeg cooker hood light fitting replacement

    you should be able to pop the lights out and then the leads with connections on should follow

    December 20, 2017 at 1:53 pm in reply to: Rangemaster induction oven top removal #452454
    Lawrence
    Participant

    Re: Rangemaster induction oven top removalhem them

    Both side panels at the front top – look for a rubber bung the size of a 5pence piece remove them ,they reveal a posi screw take them out and the deck hinges up
    If no bungs remove the side panels revealing screws in the same place ,remove and the deck hinges up

    November 8, 2017 at 6:31 pm in reply to: Beko WMB51021W #451636
    Lawrence
    Participant

    Re: Beko WMB51021W

    2904524600

  • Author
    Posts
Viewing 15 posts - 91 through 105 (of 2,138 total)
1 2 3 … 6 7 8 … 141 142 143