[Lawrence]

Re: Attention Mods

and public staff required

[Lawrence]

Re: SMEG HINGES FOR A1-5

cometgav wrote:Hi Martin (323) yer tried the pins. Just can’t position the hinges far enough back in to the female hinge to lock them into place so you can remove the pin. Its like they are too big and wont slot in past the front cabinet.

If its the pin hinges I had a pair that almost reduced me to tears once ,the trick is to open the hinge out and then some !by that I mean that once you think you have it far enough give some more and it will line up another set of hinges ,I used long nose mole grips I think to hold it at the first stage ,but maybe if you could put them in a vice and pin them out before you go that would be easier .

[Lawrence]

Re: Next…

I have found the document that their guidance reffered to on their website,having checked our updated document against their criteria I think we are covered apart from enforcement upon which I have asked for their guidance and an example of what we should be looking at .
I have also tried to start lining ducks up ready for when they press the green button to consumer test it ,Ken is getting a written confirmation from Kev Brown with regard to indemnities,John will do a cust care survey .
I am just waiting on them now
Lawrence

[Lawrence]

Re: Next…

I must be tired ,I was thinking theres only going to be Tina …then the penny dropped .
by the way I have e-mailed the COP over to the OFT for an opinion on what we have got so far,still nothing from Adie though ,hopefull have some feed back before the mtg ,we need an agenda or at least key points .
COP
Strategy
UKW -Ken you mentioned something in a previous post
the future

[Lawrence]

Re: servis washer dryer

what is the intermittent fault ?

[Lawrence]

Re: SMEG HINGES FOR A1-5

I think you need part no 931330532 these lock with the tab latch on the hinge not the pin .I went to an A1-1 today and they fitted no worries

[Lawrence]

Re: Next…

in the bar ,in the corner like last time I reckon .
date okay by me.
Room for one please

[Lawrence]

Re: ISE machines

yes they are ASKO and they are as reliable as they always were as for supply PM KWatt for info or he may post a reply

[Lawrence]

Re: Next…

agreed face to face is needed ,mainly for strategy and a way forward .

[Lawrence]

Re: Next…

Dates -24th April,may 1st,may 8th (rather not but can if pushed )or then I am into June .
Or as Steve says we do a lot of e-mailing ,or is conference calling an option ?

[Lawrence]

Re: Refrigeration Legislation

Through my youth work side of things I have seen so much wasted money on stupid projects when there could have been funding to make a diffrence on the ground its criminal ,but from a WTA perspective , are we not better on the inside p~#~ing out ,not on the outside Pi@/#ng in whilst being accused of not bothering to take notice of something that is going to affect our trade one way or another ,just because we are “cosy,cosy” doesn’t mean that we can’t make some very salient points ,and we all know Ian can be salient 😉 .

[Lawrence]

Re: Servis M6006-1W

Washman wrote:Hi

this board may need to be reprogrammed with the Janus code so you need the Janus programmer to do this .

Mike
I thought the top board programmed the bottom board ,Dave check your edge connectors they sometimes lose tension .

[Lawrence]

Re: Can You Hear At The Back?

Penguin45 wrote:Maybe not…….. I could probably nick the induction loop system from church just for Jim, though. 😀

Chris.
😆 😆

[Lawrence]

Re: Next…

I think Coventry again if thats okay with people ,I am still trying to sort a date and can I suggest a Friday night leaving lunchtime Sat ?
With regard to Adie I have sent an e-mail that you should all recieve as well .

[Lawrence]

Re: Can You Hear At The Back?

Absolutely ,we need one desperately then maybe everyone will listen at the back as well .

[Author]

Posts