lerch

Forum Replies Created

Viewing 15 posts - 211 through 225 (of 353 total)
  • Author
    Posts
  • in reply to: Bosch WTL6003uk/17 #260427
    lerch
    Participant

    Re: Bosch WTL6003uk/17

    No should only run about every 5 minutes if I remember correctly but this is a white knight badge as bosch.

    in reply to: Zan WD not drying #260405
    lerch
    Participant

    Re: Zan WD not drying

    I have tried changing the coil only before and still had the same fault E10 best to change the triple valve then no recall. 😀

    Should be part number 1249472117

    in reply to: British Gas Engineers #260468
    lerch
    Participant

    Re: British Gas Engineers

    No less time than at Comet.

    in reply to: aeg washer dryer L16830 #260213
    lerch
    Participant

    Re: aeg washer dryer L16830

    So you have lost a netural somewhere from the pcb or on the circuit jump a netural across and see if works and go form there. 😀

    in reply to: aeg washer dryer L16830 #260211
    lerch
    Participant

    Re: aeg washer dryer L16830

    If your getting power to elements during drying cycle that would say that the pcb is ok but your elements or stats are at fault. Are you getting a live and netural feed ?

    in reply to: samsung P1453 heater #259854
    lerch
    Participant

    Re: samsung P1453 heater

    Got the part number for a J1435 / P1253GW should be the same.

    DC47-00007A WASH HEATER.

    😀

    in reply to: Servis M6002W #260197
    lerch
    Participant

    Re: Servis M6002W

    Buy a universal askol from electrue should fit and just change pump and not housing as well. Just an idea.

    in reply to: Servis m6102w #260179
    lerch
    Participant

    Re: Servis m6102w

    Should be one of the ones below (off model m6135)

    530000102 DOOR BLOCK DATE RANGE – 01/01/1900 03/03/2003

    530001500 DOOR BLOCK DATE RANGE – 03/03/2003 31/12/4999

    🙂

    in reply to: Servis M9150W Washer Dryer plastic chamber required #260202
    lerch
    Participant

    Re: Servis M9150W Washer Dryer plastic chamber required

    The white plastic pipe from the pump go’s upto the pressure pipe / switch ❓ if so all it is, is a air chamber to feed pressure upto the pressure switch.

    in reply to: aeg washer dryer L16830 #260209
    lerch
    Participant

    Re: aeg washer dryer L16830

    daft question do you have power to the elements ???

    in reply to: Hotpoint f/f defrost alert #259804
    lerch
    Participant

    Re: Hotpoint f/f defrost alert

    yes you do have braze the unit pipes

    in reply to: Hotpoint f/f defrost alert #259802
    lerch
    Participant

    Re: Hotpoint f/f defrost alert

    you have to change the divertor valve and regas.

    in reply to: Hotpoint f/f defrost alert #259798
    lerch
    Participant

    Re: Hotpoint f/f defrost alert

    The new ff range of f/freezers do this when there has been a power cut and maintain a temp of zero so that food will not re-freeze and give you food poisoning. Just press button to reset. Been to one today where only fridge getting cold divertor valve was stuck. Hope this helps.

    in reply to: Computer nerd required #243172
    lerch
    Participant

    Re: Computer nerd required

    I am abit surprized to hear that as my brother uses his for computer programming, both windows and linux never had a single fault and its 3- years old. ❓ ❓

    If you think they are bad try pcworld, I bought my one some 4-5 years ago and paid £1200 for it including a 5 year warranty.

    Gave me nothing but trouble from within 6 weeks only help I got was to keep formatting the hard drive and this was the tech. people / store manager.

    In the end give it to my nephew and built one – alot easier than you think. Took me about 1/2 hr only pain was installing windows and all the updates etc but I have very few problems. 😀

    in reply to: Indesit WIDL146 #259326
    lerch
    Participant

    Re: Indesit WIDL146

    From serial number 80414.0000 a new style dispensor hose with an intergal weir has been develoed to over come the problem of steam escaping during the drying process.

    Old style part number:- c00115450

    New style part number:- c00260015

    hope this helps 😀

Viewing 15 posts - 211 through 225 (of 353 total)