Forum Replies Created
-
Posts
-
Re: Hotpoint Aquarius Soap Tray Leakage
yes only last week i changed one for the very same fault and it worked (so far) part number we got from SEME thats dispenser complete
Re: Electrolux ESI600 Heater?
sounds like you had a blocked presure system and should not trip the rcd but a heater down to earth would
Re: Diplomat Model ADP 8132 Type 12043 Error Code ?
when does the fault happen at the start or does it fill with water, wash then the fault appears if so poss not heating
Re: Waste of a waste.
Why have Zanussi changed the style of there outlet hoses I had to install one today
Had trouble fitting the outlet and to add to that the 10mm transit bolts were rounded off and had to undo them with a screwdriver ive now got arms like PopeyeRe: Hotpoint Aquarius Soap Tray Leakage
if it floods out as soon as the water enters the machine
Then dispenser/tub blocked with soap as advised by Penguin45 or if it
Just dribbles out it is usually the dispenser top that needs changing
can be cleaned does not always workRe: Is WashVac’s site down?
yes had trouble yesterday could not get washvac or partscenter on line they must be upgrading there website as I said good luck
John
Re: Is WashVac’s site down?
Andy, washvacs website is no longer they are now parts center if you have a account, your account number log in has changed, email them and they will give you a new account number also have to fill a new form takes 2 to activate, im still waiting
click on link below
http://www.partscenter.co.ukRe: Hotpoint TDC32 Tumble Dryer – help
if drum turns without much effort its possible the belt is broken the buzzing noise is the belt pulley draging on the motor shaft remove mains lead remove top and see if you can see the belt around the drum if not then new belt is required not a diy job
Re: zanussi d/washer DE6854 fault codes
SOI/DT 12.02 LF 34/35 599 35 59-
checked last.
DEFINITION OF ALARMS
Code Leds
INTERVENTION POSSIBLE CAUSES
WATER FILL TIME-OUT
Correct level not reached.
Pressure switch does not switch to
“FULL” (1-3) within the maximum
time after activation of the solenoid
a) Tap closed
b) Water mains pressure <0.3 bar
c) Fill solenoid / connections interrupted
d) Pressure switch faulty / false contacts
e) Tube between sump and pressure switch obstructed or
leaking [AL5] [L9]
PRESSURE SWITCH ON
“EMPTY” (1-2)
Pressure switch does not return to
“FULL” (1-3) within the maximum
limit
a) Central filter clogged
b) Excessive foam
c) Dishes upside down
d) Siphon created in drain hose
[AL6] [L10] WATER DRAIN
TIME-OUT
a) Domestic drain outlet unsuitable/obstructed
b) Drain hose kinked
c) Drain pump / connections interrupted
d) Pressure switch faulty (jammed on 1-3)
e) Control board
[AL4] [L9] + [L10] INTERVENTION OF ANTIFLOODING
DEVICE
a) Water leakage from various couplings
b) Floating sensor jammed
c) Float microswitch faulty
* [AL3] [L11]
WATER HEATING
TIME-OUT
Water does not reach correct
temperature within 45 minutes
after the heating element switches
on
a) Heating element interrupted
b) Safety thermostat open
c) Wiring interrupted / false contacts
d) NTC sensor faulty / Poor thermal contact
e) Insufficient water circulation to upper spray arm
f) Washing pump (impeller stripped)
* [AL1]
“NTC” SENSOR SHORTCIRCUITED
Range < 400 Ω
a) Temperature sensor faulty (short-circuit)
b) Wiring short-circuited
c) Temperature too high (>90°C)
* [AL2]
[L9] + [L11]
“NTC” SENSOR OPEN
Range > 30.000 Ω
a) Temperature sensor faulty (open)
b) Wiring interrupted/disconnected
c) Temperature too low (< -10°C)
[AL7] [L10] + [L11] WASHING MOTOR
INOPERATIVE
a) Motor winding interrupted/short-circuited
b) False/interrupted electrical contacts
c) Motor jammed by foreign bodies
d) Capacitor interrupted/short-circuited
e) Tachymetric sensor interrupted / short-circuited
[AL8] [L9] + [L10]
+ [L11]
WASHING MOTOR ALWAYS
RUNS
a) Control board (Triac short-circuited)
In ALARM conditions [AL4], [AL5], [AL6], [AL7], [AL8] Operation of the dishwasher is interrupted and the corresponding LEDS flash.
To cancel the ALARM Press [S0] to switch off the appliance.
When the dishwasher is switched on again The cycle resumes from the point at which it was interrupted.
* In ALARM conditions – [AL1]/[AL2], [AL3] The cycle is completed without any error displayed to the user. The problem is simply
stored in memory for examination by a Service Engineer (see section 6.1).
hope this works for you
