loopey

Forum Replies Created

Viewing 15 posts - 181 through 195 (of 406 total)
  • Author
    Posts
  • in reply to: Hoover Vision HD 8kg #340643
    loopey
    Participant

    Re: Hoover Vision HD 8kg

    i need an email addy to send you a little reading 🙂

    in reply to: servis M6713W #340642
    loopey
    Participant

    Re: servis M6713W

    thank you kind sir 🙂

    in reply to: hoover dw #340464
    loopey
    Participant

    Re: hoover dw

    Have sent you a little lite reading lol .. night time 4 hour wash system what will they think of next , hth

    phil

    in reply to: tumble dryers out side #340460
    loopey
    Participant

    Re: tumble dryers out side

    yeah weve had the same on a lot of electronic dryers , have been told anything below 5 degrees the ntcs will be out of range ,

    in reply to: Bosch kgv3120gb/01 #340066
    loopey
    Participant

    Re: Bosch kgv3120gb/01

    look here 🙂

    http://www.ukwhitegoods.co.uk/modules.p … c&start=15

    in reply to: Hoover HCA394FKPW #339793
    loopey
    Participant

    Re: Hoover HCA394FKPW

    you were lucky just locking up to go home

    check your inbox

    happy new year to all

    see yer next year 🙂
    phil

    in reply to: Hoover HCA394FKPW #339791
    loopey
    Participant

    Re: Hoover HCA394FKPW

    Hi i need an email addy to send you a little lite reading

    error 01 is COMMUNICATION TROUBLES BETWEEN
    THE CONTROL AND THE DISPLAY
    BOARDS, FOR MORE THAN 1 MINUTE.

    in reply to: hoover vhd9143zd #339827
    loopey
    Participant

    Re: hoover vhd9143zd

    dont put a fuse in it it will go bang trust me 🙂


    The fuse identified as M in Picture 2, is protecting the Core Board from fire. In case it’s
    found burned out, it cannot be replaced but must be replaced the whole Core Board.
    Ref. in
    Pic. 2
    Type of Electronic
    Component on Board
    Electromechanical controlled Component


    simonb look in your in box 🙂

    in reply to: Merry Christmas #339350
    loopey
    Participant

    Re: Merry Christmas

    Merry Christmas every one have a ggod un

    phil

    in reply to: Hotpoint FF40P Error indications ? #339546
    loopey
    Participant

    Re: Hotpoint FF40P Error indications ?

    yes just get the customer to turn both dials to off then all the way to on and then back should reset it ..

    phil

    in reply to: beko drum paddles / welded tubs ? #339072
    loopey
    Participant

    Re: beko drum paddles / welded tubs ?

    yo helo . thanks guys will give it a whirl 🙂

    in reply to: beko drum paddles / welded tubs ? #339069
    loopey
    Participant

    Re: beko drum paddles / welded tubs ?

    Thanks martin but how do you get the old shaft off ,its in between the 2 skins of the tub ?? . no scews no nothing its punched together . or am i being blonde ?:)

    The C00113038 you gave me is the standard kit fitted thousands of them

    in reply to: beko drum paddles / welded tubs ? #339067
    loopey
    Participant

    Re: beko drum paddles / welded tubs ?

    is60v indesit crap dryer have gone the same way drum shaft punched on

    its BER

    in reply to: Hoover Dishwasher HND6515 #339043
    loopey
    Participant

    Re: Hoover Dishwasher HND6515

    yes o/c its a pressure switch controls the heater

    in reply to: Hoover HNC380-80 condenser dryer, stopping after reversing #338282
    loopey
    Participant

    Re: Hoover HNC380-80 condenser dryer, stopping after reversi

    40003258 NTC probe

    5045171534522

    there you go 🙂 i think thats what you need

Viewing 15 posts - 181 through 195 (of 406 total)