Forum Replies Created
-
Posts
-
Re: Hoover Oph7174D E03 fault help please
Uploaded with ImageShack.us
This is what i found on this , hope it helps
A) DESCRIPTION OF THE TROUBLE:
We were recently informed about some seldom happenings of the trouble as quoted in subject, mainly
on Washing Machines and Washer-Dryers equipped with Electronic Power Modules of the “Cuore” type,
both by the MDL and INVENSYS makers.
In normal operational conditions, the ERROR 3 is displayed whenever the Phase of Drain is taking a
longer time than the maximum allowed 4′ and 30″. The most frequent reasons for the displaying of the
ERROR 3 are the clogged Filter of the Drain Pump, the bent and/or clogged Drain Hose, an obstruction
in the wall drainage system and of course a defective Drain Pump. On the contrary, in the here
mentioned cases the ERROR 3 was randomly displayed by Appliances whose drain circuit was in perfect
conditions and whose Drain Phases were carried out within the designed limit of time. Nevertheless,
the ERROR 3 was displayed and when this happened, the currently running Washing Cycle was halted.
B) REASONS AND SOLUTION OF THE TROUBLE:
After a careful examination, we realized that the common factor to all
Appliances showing the trouble as in subject, was a slight current leak
on the grounding of the Water Heating Element, this sending a
misleading signal to the “Cuore” Power Module.
Therefore should you happen to face a trouble like the above
described, we suggest to disconnect, insulate end safely fix far
from the moving parts, the two connectors of the Water Heating
Element (indicated in the picture). Next, carry out a whatever short
Washing Cycle with a Phase of Heating.
In case of INVENSYS Power Module, the ERROR 14 (Missing Water
Heating: defective NTC Probe and/or Water Heating Element and/or
Wiring) could be displayed. Contrary to what happens with the ERROR
3, ERROR 14 doesn’t halt the currently carried out Washing Cycle.
Should the Washing Cycle be correctly brought to the end, without any
ERROR 3 being displayed and being all the Drain Phases correctly
performed, then please replace the Water Heating Element with
another one of the same type and supplied by GIAS as spare part.
Best regards.
GIAS ItalyRe: hotpoint ffa97 fridge freezer pcb
Its plug n play .. Fit pcb plug in with fridge door open for 15 secounds ,
it should to a test cycle , hthphil
Re: Anyone know how to get into diag on lux int WD no model
quick fix is bend the aloi door pecker with a pair of grips to wards the door lock done loads of them , or change the pecker , very common fault on these , that and the bleedin dryer elements lol 🙁
hth phil
Re: Diplomat ADP8352 dishwasher overfills.
I am sure theres a flowmeter on these ? on the left hand side on the breather assembly ,
hth phil……..
Re: hoover dishwasher model hd97e
E3 FAULTY ELECTRIC HEATER ELEMENT
give me an email addy and will send you the full test pdf its a big un lol
its 24 pages of infoRe: hoover HCA300FK. ff flashing and freezer frozen over
i would be checking BIMETAL DEFROST
THERMOSTAT & THERMAL FUSE ASSEMBLY , iff the super freeze led is on
or flashing its a fault with that or the defrost heater …hth phil
Re: Hoover module fuse
The part that blows is (IRAMS10UP60B-2 International Rectifier Motion Motor Control, Integrated Power Module developed and optimized for electronic motor control .. so check the motor 🙂
philRe: Evaporation tray. Lux ER6641T 933002104
Take one from a scrap fridge freezer there prity much the same double sided sticky tabs will keep in place , connect have a universal one for about £3 + vat 🙂
hth phil
