[loopey]

Re: Hoover module fuse

pmb have you changed the fuse yet ? and what was the out come ?

[loopey]

Re: Hoover module fuse

The fuse identified as M in Picture 2, is protecting the Core Board from fire. In case it’s
found burned out, it cannot be replaced but must be replaced the whole Core Board.

hth phil

[loopey]

Re: Hoover module fuse

ok change the fuse , but it will do no good it will blow the pcb, they need to be reconfigured. it will blow the main multi triac lol , i no this after 5 a temps of changing fuses on different m/c s
hth phil

[loopey]

Re: Van Insurance Rip Off

Slightly off topic , tried to get insurance for 17 year old. past his test took the lad on and we get stumped for ,( are you sitting down folks )£3.500k
the lads gutted he carnt drive works van , it sits there all week doing nothing , and a reduntant delivery driver looking very sad . dont that just suck 🙁

[loopey]

Re: Hoover HCF 6200 A. temp probe location

Your most welcome 🙂

[loopey]

Re: SIMPLE PCB REPAIR TIPS

Hi , Martin how do you do the red arrow and text on pics , i like it lol beets my marker pen lol

[loopey]

Re: SIMPLE PCB REPAIR TIPS

electrofix wrote:quite a few dishwashers use a 1uf or 1.5uf capacitor as a power supply for the pcb
when these go it is like having a low battery

fault you expect dishwasher turns on set prog
prog starts and dishwasher fills as soon as main motors switches on it all goes pear shaped (ie not enough power to hold in motor relay )

similar problem on the old hoover tumble dryers small pcb that start td
replace small cap (think its .22uf from memory) board repaired repair cost less than 50p

can supply part suppier info if reqd

Dave

all good dave have the same looking probs with lux aeg zan frost free f/f
and most hotpoint single board f/f

this below is the hotpoint indeshit boards 1uf or 1.5uf appears to be on wont run the compressor change it all is well

the same with the lux zan boards

And the bosch conversion , fridge warm freezer ok cuts out the the fridge thermister , will post the 3 wire when i see one ? 🙂

[loopey]

Re: Hoover HCF 6200 A. temp probe location

should be somethig in yer in box 🙂 DOCTORDOOM

[loopey]

Re: Hoover Hspf 157

should be some thing in yer inbox:)

[loopey]

Re: Indesit DI 620

water in base most likley a leak ,

[loopey]

Re: Hoover HFA270 fridge freezer freezing in the fridge

should be some thing in yer in box 🙂

[loopey]

Re: Hoover Hspf 157

need a email address , will send you a pdf file 🙂

[loopey]

Re: CPCA240FSK temp probe

Find out the indicated position, on the
outer back wall of the appliance (Ref. X
in Picture 11). This is the exact centre
of the window, to be opened next.
Dimension H (measured from the top
edge of cabinet): 168 mm.
Dimension L (measured from the left
side edge of cabinet): 172 mm.

gimme a bell lol with yer email addy will send you pdf walk through its dead easy lol

[loopey]

Re: Hoover HCF 6200 A. temp probe location

from the back with the condensor removed Find out the indicated position, on the
outer back wall of the appliance (Ref. X
in Picture 11). This is the exact centre
of the window, to be opened next.
Dimension H (measured from the top
edge of cabinet): 168 mm.
Dimension L (measured from the left
side edge of cabinet): 172 mm.

give me a email address and will send you pdf walk through 🙂

hth

[loopey]

Re: Hoover HFA270 fridge freezer freezing in the fridge

49003477 going to send you a little some thing all i need is a email address

[Author]

Posts