Martin

Forum Replies Created

Viewing 15 posts - 3,496 through 3,510 (of 25,534 total)
1 2 3 … 233 234 235 … 1,701 1,702 1,703
  • Author
    Posts
  • November 21, 2014 at 8:15 pm in reply to: electrolux EOD982b grill element wiring #421808
    Martin
    Participant

    Re: electrolux EOD982b grill element wiring

    slyp98 wrote:

    martinm wrote:
    need a serial number as there are a few different wiring varations

    24200016

    This should be the correct diagram….

    November 21, 2014 at 8:08 pm in reply to: bosch sms40c02gb water flow problem #421792
    Martin
    Participant

    Re: bosch sms40c02gb water flow problem

    Yes it is removable and THIS is the part you need.

    November 21, 2014 at 10:50 am in reply to: The eBay revolution #421799
    Martin
    Participant

    Re: The eBay revolution

    They do quite well on Amazon too. Ain’t that there interweb wonderful?

    November 21, 2014 at 10:46 am in reply to: New Miele or repair 8 year old one #421812
    Martin
    Participant

    Re: New Miele or repair 8 year old one

    How do you know the repair cost will total £250?
    What happens if it costs even more once the repair work begins?
    In its 8 years service has it been flogged to death with daily wash loads?
    If money is of little concern then why ask? Go get a new one. 😀
    Personally speaking I would take the repair option, but then I couldn’t afford to spend over a grand on a new one anyway.
    How long IS a piece of string? :clown:

    November 21, 2014 at 7:01 am in reply to: hotpoint dryer tdc 32 #421125
    Martin
    Participant

    Re: hotpoint dryer tdc 32

    Amen!

    November 21, 2014 at 6:59 am in reply to: Removing Bolts From Feet #421795
    Martin
    Participant

    Re: Removing Bolts From Feet

    Not really.

    November 20, 2014 at 7:38 pm in reply to: bosch sms40c02gb water flow problem #421789
    Martin
    Participant

    Re: bosch sms40c02gb water flow problem

    The reed switch is located in the centre of the fill matrix. Costs about a tenner to replace.

    November 20, 2014 at 6:20 pm in reply to: Bosch coding info #421756
    Martin
    Participant

    Re: Bosch coding info

    Dispenser shouldn’t open in a pre-rinse, so perhaps the Control Unit was never configured from when the BSH contractors replaced it. I will dig out the coding instructions if you pm your direct email address. 😀

    November 20, 2014 at 5:15 pm in reply to: Washing machine always heating water #421780
    Martin
    Participant

    Re: Washing machine always heating water

    Heater relay on the control board jammed on.

    November 20, 2014 at 3:47 pm in reply to: Bosch coding info #421754
    Martin
    Participant

    Re: Bosch coding info

    Dispenser solenoid corrupted the Control Unit probably.

    November 19, 2014 at 10:33 pm in reply to: Zanussi ZWD1662 “stopping mid cycle” #421737
    Martin
    Participant

    Re: Zanussi ZWD1662 “stopping mid cycle”

    Subs changed the element Steve.

    November 19, 2014 at 6:24 pm in reply to: Bosch coding info #421751
    Martin
    Participant

    Re: Bosch coding info

    Have you changed the control Unit then?

    November 19, 2014 at 5:05 pm in reply to: Amica AWE512L #421747
    Martin
    Participant

    Re: Amica AWE512L

    So I take it you have checked the motor? (as the error code suggests) 😉

    November 19, 2014 at 4:32 pm in reply to: Amica AWE512L #421745
    Martin
    Participant

    Re: Amica AWE512L

    Is it like this shown in the ‘Known Error Codes’ thread?

    November 19, 2014 at 3:51 pm in reply to: cooker hood question #421616
    Martin
    Participant

    Re: cooker hood question

    lee8 wrote:Their

    Very good lee, you spotted the wind up. Take the rest of the day off as a reward. 🙂

  • Author
    Posts
Viewing 15 posts - 3,496 through 3,510 (of 25,534 total)
1 2 3 … 233 234 235 … 1,701 1,702 1,703