Martin114

Forum Replies Created

Viewing 15 posts - 136 through 150 (of 334 total)
1 2 3 … 9 10 11 … 21 22 23
  • Author
    Posts
  • May 24, 2010 at 6:32 pm in reply to: Whirlpool PCB? #320960
    Martin114
    Participant

    Re: Whirlpool PCB?

    Yes they do but I’ve found the vitrous enameled ones from rs components are very good. I think 2.5 to 3 watt would be better.
    Also the pcb is double sided so it might be easier to snip the leads leaving enough stems to solder to

    May 24, 2010 at 6:18 pm in reply to: Whirlpool PCB? #320958
    Martin114
    Participant

    Re: Whirlpool PCB?

    Could be the 22 ohm 2 watt wirewound resistor gone o/c Jim.

    May 6, 2010 at 2:44 pm in reply to: Hotpoint WF840 Stuck on 1min #319538
    Martin114
    Participant

    Re: Hotpoint WF840 Stuck on 1min

    Sounds like o/c heating element

    April 5, 2010 at 11:48 pm in reply to: They dont build em like that anymore – Part 20 #309243
    Martin114
    Participant

    Re: They dont build em like that anymore – Part 20

    Zanussi built hotpoint 1826?

    February 26, 2010 at 3:15 pm in reply to: BEKO No go #313282
    Martin114
    Participant

    Re: BEKO No go

    Sounds like you just need to cancel the Child Lock

    February 1, 2010 at 7:28 pm in reply to: Whirlpool w/machine awo/d5706 #310689
    Martin114
    Participant

    Re: Whirlpool w/machine awo/d5706

    THIS might help!

    January 7, 2010 at 6:15 pm in reply to: whirlpool awo/d4705.DEAD #308157
    Martin114
    Participant

    Re: whirlpool awo/d4705.DEAD

    If not it will be the 22 ohm 2 watt wirewound resistor on the module

    December 2, 2009 at 9:09 pm in reply to: Bosch SMS50E06GB/02 – E24 #305489
    Martin114
    Participant

    Re: Bosch SMS50E06GB/02 – E24

    Thanks for the reply, yes I checked the pump chamber cover and it was firmly clipped in place.

    August 24, 2009 at 6:23 am in reply to: Indesit WIL163s uk #295306
    Martin114
    Participant

    Re: Indesit WIL163s uk

    I would guess heating element o/c

    August 22, 2009 at 7:25 am in reply to: BEKO WMA745W #295234
    Martin114
    Participant

    Re: BEKO WMA745W

    Could it be the ‘child lock’ set? I know that would be CL but you never know!

    August 17, 2009 at 9:34 am in reply to: 10 – Drumming #280534
    Martin114
    Participant

    Re: 10 – Drumming

    ordered the heavy duty ones Jim.

    August 17, 2009 at 9:00 am in reply to: 10 – Drumming #280532
    Martin114
    Participant

    Re: 10 – Drumming

    I know what you mean Steve, but the ones I ordered are Self-adhesive 3mm bitumen damping panels and are listed as suitable for sound deadening of engine compartments etc, so it would seem to be similar to what Chris has used.

    Cheers,
    Martin

    August 17, 2009 at 12:03 am in reply to: 10 – Drumming #280530
    Martin114
    Participant

    Re: 10 – Drumming

    I also have had a customer telling me about her 10 making a very loud noise on spin so I have ordered some anti-vibration sheets from here in preparation for a visit.

    July 22, 2009 at 8:43 pm in reply to: Sold faulty Machines #292627
    Martin114
    Participant

    Re: Sold faulty Machines

    Hi folks, Its just a 22 ohm 2 watt wirewound resistor that is required.
    This Thread should help 😀

    July 18, 2009 at 9:32 am in reply to: ISE 10 F3 Fault Code Help please #292523
    Martin114
    Participant

    Re: ISE 10 F3 Fault Code Help please

    Usually caused by 5p coin or similar jamming pump impeller.
    just remove filter (after draining via small hose behind filter door) and look inside pump.

  • Author
    Posts
Viewing 15 posts - 136 through 150 (of 334 total)
1 2 3 … 9 10 11 … 21 22 23